null

Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Efficient Extraction of By-Products for Sale to the Market

06.05.2008
Siemens Modernizes Coke-Oven By-Product Plant at Isdemir, Turkey

A project comprising the expansion and modernization of a coke-oven by-product plant, which Siemens Metals Technologies implemented for the Turkish steel producer Isdemir, was completed in February 2008. Two semi-separate gas-treatment lines are now in operation, increasing the processing capacity from 70,000 to 140,000 Nm3 of coke-oven gas per hour.

This allows Isdemir to extract and sell approximately 40,000 tons t/a of ammonium sulfate, 75,000 t/a of tar and 30,000 t/a of benzol. At the same time, environmental emissions are significantly reduced. The process automation supplied by Siemens enables plant monitoring and operating functions to be carried out from a central control pulpit. Precise monitoring and process control ensures that the plant achieves highest efficiency at a high level of quality control and operational safety.

As part of a campaign to expand the production of steel to approximately 6.25 million tons by the end of 2009, the Turkish steel producer Isdemir, located in Iskenderun (Hatay Province) on the Mediterranean coast, is modernizing and expanding its production facilities. In order to meet the increased coke demands for a new blast furnace currently under construction, two additional coke-oven batteries (No. 5 and No. 6) were built to increase the coke production from 1.2 to 2.4 million tons per year. This necessitated an expansion and modernization of the existing coke-oven by-product plant to treat the increased quantities of generated coke-oven gas.

The project scope included the engineering and supply of mechanical equipment, instrumentation, electrics and automation as well as the supervision of construction and commissioning. A central part of the project is the new automation and process control technology.

Level 1 automation is comprised of the fully redundant Simatic PCS7 DCS system to ensure that the plant has near-zero downtime. Level 2 automation is equipped with a historian analysis system to support process performance investigations and also SPC (statistical process control) analyses, providing the operator with a basis for continuous optimization of the process. All plant and process data are now readily available in a central control room, facilitating plant operations and monitoring. Precise knowledge of all the relevant information supports the personnel at achieving highest efficiency with respect to the removal of ammonia, BTX (benzene, toluene and xylene) or tar from the coke-oven gas. The operation software was designed and developed to enable early detection of process or equipment problems.

Extensive mechanical equipment upgrading and installations were also carried out by Siemens. This included the sand-blasting and retubing of the existing ten primary coolers of the primary gas-cooling system as well as the installation of two new primary coolers. The cooling towers for primary gas cooling were also refurbished – two new cells were added along with filtration and chemical-dosing systems. Eight tar precipitators were completely rebuilt, using only the shells of the existing units. The entire gas-exhaust system was overhauled to cope with the increased gas quantities.

The ammonium sulfate production and drying section was completely demolished and reconstructed as two production lines comprising three new ammonia absorbers and two independent crystallizing lines. The three serial crude-benzene scrubbers in each of the two independent production lines were upgraded to increase their capacity. Furthermore, the crude benzene recovery line was completely rebuilt. Two new high-efficiency flushing-liquor and tar decanters were installed to handle higher outputs. The ammonia liquor distillation section was reconstructed to enhance the settling and stripping of ammonia to boost ammonium sulfate production as well as to satisfy strict environmental regulations. The existing cooling towers for final cooling were demolished and rebuilt with filtration and chemical-dosing systems.

A completely new foul-water system was also supplied and the biological effluent-treatment line was completely overhauled to comply with stricter environmental regulations.

Additional information on solutions for steel works, rolling mills and processing lines is available at http://www.siemens.com/metals.

The Siemens Industry Sector (Erlangen, Germany) is the world's leading supplier of production, transportation and building systems. Integrated hardware and software technologies combined with comprehensive industry-specific solutions enable Siemens to enhance the productivity and efficiency of its customers in industry and infrastructure. The Sector comprises six Divisions: Building Technologies, Industry Automation, Industry Solutions, Mobility, Drive Technologies and Osram. In fiscal 2007 (ended September 30), Siemens Industry generated sales of approximately EUR40 billion (pro forma, unconsolidated) with around 209,000 employees worldwide. http://www.siemens.com/industry

With the business activities of Siemens VAI Metal Technologies, (Linz, Austria), Siemens Water Technologies (Warrendale, Pa., U.S.A.), and Industry Technologies, (Erlangen, Germany), the Siemens Industry Solutions Division (Erlangen, Germany) is one of the world's leading solution and service providers for industrial and infrastructure facilities. Using its own products, systems and process technologies, Industry Solutions develops and builds plants for end customers, commissions them and provides support during their entire life cycle.


Further information:

Anzeige

Anzeige

Event News

ICTM Conference 2017: Production technology for turbomachine manufacturing of the future

16.11.2016 | Event News

Innovation Day Laser Technology – Laser Additive Manufacturing

01.11.2016 | Event News

#IC2S2: When Social Science meets Computer Science - GESIS will host the IC2S2 conference 2017

14.10.2016 | Event News

 
Latest News

NTU scientists build new ultrasound device using 3-D printing technology

07.12.2016 | Health and Medicine

The balancing act: An enzyme that links endocytosis to membrane recycling

07.12.2016 | Life Sciences

How to turn white fat brown

07.12.2016 | Health and Medicine

VideoLinks
B2B-VideoLinks
More VideoLinks >>>