How windproof are cable cars?

Two researchers from the Vienna University of Technology (TU) have thrown light on vibration-control problems, an area little researched up to now and were able to account for the occurrence of lateral vibrations from various wind conditions right through to meteorological calm.

A measuring system which also measures wind direction and wind velocity on a two or three-dimensional basis is positioned on the cab of a cable car or on the chair of a chair lift. The behaviour of the vehicle on impact of the wind can thereby be measured in a wholly self-supporting manner. A dip in a transverse and longitudinal direction when vibrating, the driving speed and the position of the vehicle en route are of particular importance in this regard.

Observations by operating personnel of certain cable car systems have shown that a lateral vibration of the pendulum with large tilt angles can occur not only when the crosswind is blowing gustily but also when the wind is calm. In the meantime this has been quantified using measurement data. “On the basis of this measurement data, we confirmed that the cabs undergo vibratory excitation due to continuously circulating bicable tramways at certain velocities.

In the case of certain continuously circulating bicable tramways, this phenomenon is manifested at a lower driving speed range of approximately 2.0 to 3.0 metres per second. Normal driving speeds lie between 4 and 6 m/s”, says Klaus Hoffmann, head of the Institute for Engineering Design and Logistics Engineering at the TU Vienna.

The measurements confirmed the suspicion that the afore-mentioned oscillations are due to periodical vortex shedding in the cab originating with the airsteam. Particularly strong vibrations occur when the vortex shedding frequency is identical to the natural frequency of the cab. Basically, the phenomenon can only be avoided if longer journeys are carried out at a driving speed range between 2 and 3 m/s.

“Thanks to the extensive European set of standards in accordance with which the cable cars are manufactured, there is a very high internationally comparable safety level today. Each cable car must undergo certain safety checks before it may be used by the operating company. Neveretheless, questions concerning the windproof capacity of cable cars in instruction manuals are often kept vague. Thus, the instruction manuals for monocable aerial ropeways, chair lifts or cabin tramways state the wind velocity at which the tramway can continue to be operated. At a constant crosswind of 50 to 65 km/h the availability limit of monocable aerial ropeways has normally been attained”, says Robert Liehl, a doctoral candidate at the institute. Apart from wind sensors on the supports whose data is only partly representative for wind conditions along the entire cable car, the entire cable line must also be monitored in these situations by the operating personnel using a pair of binoculars. Hoffmann: “Even for lower average wind velocities, sudden gusts of wind can lead to critical situations. Our measurement data should supply additional information to be able to provide more accurate details of the vibration behaviour of cable car vehicles during different operating conditions.”

During this research project the measuring system was patented in 2002 and has since then been used to carry out field measurements of wind loads and pendulum vibrations for different cable cars and chair lifts. Thanks to the support of the two world market leaders in cable car construction – Doppelmayr and Leitner – this measurement system can continue to be developed further.

Enquiries to:
Ao.Univ.Prof. Dipl.-Ing. Dr. Klaus Hoffmann
Vienna University of Technology
Institute for Engineering Design and Logistics Engineering
Getreidemarkt 9/Stg.4/4.Stk, 1060 Vienna
T +43/1/58801 – 30746
F +43/1/58801 – 30799
E klaus.hoffmann@tuwien.ac.at
Dipl.-Ing. Robert Liehl
Leitner GmbH
Niederlassung WIEN – VIENNA Branch
Perlhofgasse 2/1
A-2372 Gießhübl
T +43/2236 893 713 – 75
F +43/2236 893 713 – 55
E liehl.robert@leitner-lifts.com
Sent by:
Mag. Daniela Hallegger
Vienna University of Technology – PR and Communication
Karlsplatz 13/E011, A-1040 Vienna
T +43-1-58801-41027
F +43-1-58801-41093
E daniela.hallegger@tuwien.ac.at

Media Contact

Werner Sommer idw

All latest news from the category: Machine Engineering

Machine engineering is one of Germany’s key industries. The importance of this segment has led to the creation of new university degree programs in fields such as production and logistics, process engineering, vehicle/automotive engineering, production engineering and aerospace engineering among others.

innovations-report offers informative reports and articles covering technologies such as automation, motion, power train, energy, conveyor, plastics, lightweight construction, logistics/warehousing, measurement systems, machine tools and control engineering.

Back to home

Comments (0)

Write a comment

Newest articles

Pancreatic cancer’s cellular amnesia

Things aren’t always as they seem. Take pancreatic cancer, for example. In up to one in 10 cases, researchers have documented a peculiar characteristic. Some of the pancreatic cells appear…

Innovative Polymer Wound Dressings for Painless and Residue-Free Removal

A new approach enables dressings that adhere firmly to the skin at body temperature, but can be removed easily and painlessly in combination with a cold pack. The dressing adheres…

SETI Institute launches groundbreaking technosignature science and technology

Application deadline for grants is July 15, 2024. The SETI Institute is announcing the launch of a pioneering grants program dedicated to advancing technosignature science. This first-of-its-kind initiative aims to…

Partners & Sponsors