Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Phoenix Mars Lander Uses Soil Probe and Swiss Scope

11.07.2008
NASA's Phoenix Mars Lander has touched Martian soil with a fork-like probe for the first time and begun using a microscope that examines shapes of tiny particles by touching them.
Phoenix's robotic arm pushed the fork-like probe's four spikes into undisturbed soil Tuesday as a validation test of the insertion procedure. The prongs of this thermal and electrical conductivity probe are about 1.5 centimeters, or half an inch, long. The science team will use the probe tool to assess how easily heat and electricity move through the soil from one spike to another.

Such measurements can provide information about frozen or unfrozen water in the soil.

The probe sits on a "knuckle" of the 2.35-meter-long (7.7-foot-long) robotic arm. Held up in the air, it has provided assessments of water vapor in the atmosphere several times since Phoenix's May 25 landing on far-northern Mars.

Researchers anticipate getting the probe's first soil measurements following a second placement into the ground, planned as part of today's Phoenix activities on Mars.

Phoenix also has returned the first image from its atomic force microscope. This Swiss-made microscope builds an image of the surface of a particle by sensing it with a sharp tip at the end of a spring, all microfabricated from a sliver of silicon. The sensor rides up and down following the contour of the surface, providing information about the target's shape.

"The same day we first touched a target with the thermal and electrical conductivity probe, we first touched another target with a needle about three orders of magnitude smaller -- one of the tips of our atomic force microscope,"

said Michael Hecht of NASA's Jet Propulsion Laboratory, Pasadena, Calif., lead scientist for the suite of instruments on Phoenix that includes both the conductivity probe and the microscopy station.

The atomic force microscope can provide details of soil-particle shapes as small as about 100 nanometers, less than one-hundredth the width of a human hair. This is about 20 times smaller than what can be resolved with Phoenix's optical microscope, which has provided much higher-magnification imaging than anything seen on Mars previously.

The first touch of an atomic force microscope tip to a substrate on the microscopy station's sample-presentation wheel served as a validation test. The substrate will be used to hold soil particles in place for inspection by the microscope. The microscope's first imaging began Wednesday and produced a calibration image of a grooved substrate. "It's just amazing when you think that the entire area in this image fits on an eyelash. I'm looking forward to exciting things to come," Hecht said.

With these developments in the past two days, the spacecraft has put to use all the capabilities of its Microscopy, Electrochemistry and Conductivity Analyzer, or MECA, suite of instruments. Researchers have begun analyzing data this week from the second sample of soil tested by MECA's wet chemistry laboratory.

Meanwhile, the Phoenix team is checking for the best method to gather a sample of Martian ice to analyze using the lander's Thermal and Evolved-Gas Analyzer, which heats samples and identifies vapors from them. Researchers are using Phoenix's robotic arm to clear off a patch of hard material uncovered in a shallow trench informally called "Snow White." They plan in coming days to begin using a motorized rasp on the back of the arm's scoop to loosen bits of the hard material, which is expected to be rich in frozen water.

The atomic force microscope for Phoenix was provided by a consortium led by the University of Neuchatel, Switzerland.

The Phoenix mission is led by Peter Smith of the University of Arizona with project management at JPL and development partnership at Lockheed Martin, Denver. International contributions come from the Canadian Space Agency; the University of Neuchatel; the universities of Copenhagen and Aarhus, Denmark; Max Planck Institute, Germany; and the Finnish Meteorological Institute. For more about Phoenix, visit: http://www.nasa.gov/phoenix and http://phoenix.lpl.arizona.edu.

MEDIA CONTACTS:
Guy Webster, Jet Propulsion Laboratory
(818-354-6278; guy.webster@jpl.nasa.gov)
Sara Hammond, University of Arizona
(520-626-1974; shammond@lpl.arizona.edu)
J.D. Harrington, NASA Headquarters
(202-358-5241; j.d.harrington@nasa.gov)

Lori Stiles | University of Arizona
Further information:
http://www.nasa.gov/phoenix
http://phoenix.lpl.arizona.edu

More articles from Physics and Astronomy:

nachricht From rocks in Colorado, evidence of a 'chaotic solar system'
23.02.2017 | University of Wisconsin-Madison

nachricht Prediction: More gas-giants will be found orbiting Sun-like stars
22.02.2017 | Carnegie Institution for Science

All articles from Physics and Astronomy >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: Breakthrough with a chain of gold atoms

In the field of nanoscience, an international team of physicists with participants from Konstanz has achieved a breakthrough in understanding heat transport

In the field of nanoscience, an international team of physicists with participants from Konstanz has achieved a breakthrough in understanding heat transport

Im Focus: DNA repair: a new letter in the cell alphabet

Results reveal how discoveries may be hidden in scientific “blind spots”

Cells need to repair damaged DNA in our genes to prevent the development of cancer and other diseases. Our cells therefore activate and send “repair-proteins”...

Im Focus: Dresdner scientists print tomorrow’s world

The Fraunhofer IWS Dresden and Technische Universität Dresden inaugurated their jointly operated Center for Additive Manufacturing Dresden (AMCD) with a festive ceremony on February 7, 2017. Scientists from various disciplines perform research on materials, additive manufacturing processes and innovative technologies, which build up components in a layer by layer process. This technology opens up new horizons for component design and combinations of functions. For example during fabrication, electrical conductors and sensors are already able to be additively manufactured into components. They provide information about stress conditions of a product during operation.

The 3D-printing technology, or additive manufacturing as it is often called, has long made the step out of scientific research laboratories into industrial...

Im Focus: Mimicking nature's cellular architectures via 3-D printing

Research offers new level of control over the structure of 3-D printed materials

Nature does amazing things with limited design materials. Grass, for example, can support its own weight, resist strong wind loads, and recover after being...

Im Focus: Three Magnetic States for Each Hole

Nanometer-scale magnetic perforated grids could create new possibilities for computing. Together with international colleagues, scientists from the Helmholtz Zentrum Dresden-Rossendorf (HZDR) have shown how a cobalt grid can be reliably programmed at room temperature. In addition they discovered that for every hole ("antidot") three magnetic states can be configured. The results have been published in the journal "Scientific Reports".

Physicist Dr. Rantej Bali from the HZDR, together with scientists from Singapore and Australia, designed a special grid structure in a thin layer of cobalt in...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

Booth and panel discussion – The Lindau Nobel Laureate Meetings at the AAAS 2017 Annual Meeting

13.02.2017 | Event News

Complex Loading versus Hidden Reserves

10.02.2017 | Event News

International Conference on Crystal Growth in Freiburg

09.02.2017 | Event News

 
Latest News

Stingless bees have their nests protected by soldiers

24.02.2017 | Life Sciences

New risk factors for anxiety disorders

24.02.2017 | Life Sciences

MWC 2017: 5G Capital Berlin

24.02.2017 | Trade Fair News

VideoLinks
B2B-VideoLinks
More VideoLinks >>>