Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

COPD patients at risk of dangerous bacterial infections

16.01.2013
It is well known that COPD patients run a higher risk of contracting respiratory infections. However, a new thesis from Lund University in Sweden shows that they are also at higher risk of other bacterial infections, such as tuberculosis (TB) and pneumococcal and staphylococcal infections that can cause serious illness.
The abbreviation COPD stands for chronic obstructive pulmonary disease and the disease makes it difficult for patients to breathe. However, the disease affects other organs as well as the lungs. It is also linked to an increased risk of conditions such as diabetes, cancer and heart failure.

“Despite this, until now most focus has been on respiratory infections; infections in other organs have not been studied to the same extent”, says Dr Malin Inghammar.

In her thesis, Dr Inghammar has shown that individuals in Sweden who have been diagnosed with COPD have a three times higher risk of active tuberculosis than the population in general. They are also at higher risk of invasive pneumococcal disease, a type of infection that can cause meningitis and septicaemia.

In another study, Malin Inghammar has looked at the presence of bacteria in the blood of COPD patients and control subjects from the general population. A wide range of bacteria, such as coliform bacteria and staphylococcus aureus, were seen to be 2.5 times more frequent in the blood of patients with COPD.

Tuberculosis is a rare disease in Sweden, so the association between COPD and TB is not of great importance in Sweden. However, the association could be important for countries such as India and China, where TB is still a common disease and where smoking is on the increase. Doctors may need to have increased awareness of dangerous infection-causing bacteria in any country.

“The next step is to study what causes the link. Does the cortisone treatment that is usually given to COPD patients make them vulnerable to infections? Or is the susceptibility to infection due to other factors, such as the weight loss, muscle weakness and anaemia that are associated with the condition?” asks Malin Inghammar.

Her findings could in the future lead to changes in the treatment of COPD. If COPD patients are at extra high risk of hospital-acquired infections, then perhaps more care should be taken before admitting them to hospital, and greater reflection made on all the factors that could entail an increased risk of infection.

The thesis is entitled Epidemiological studies of severe infections in COPD and was presented on 11 January.

Malin Inghammar can be reached on +46 709 10 39 97 or malin.inghammar@med.lu.se

Helga Ekdahl Heun | idw
Further information:
http://www.vr.se
http://www.lunduniversity.lu.se/o.o.i.s?id=12683&postid=3233372

More articles from Health and Medicine:

nachricht New leukemia treatment offers hope
23.09.2016 | King Abdullah University of Science and Technology

nachricht Alzheimer’s: Cellular Mechanism Provides Explanation Model for Declining Memory Performance
21.09.2016 | Deutsches Zentrum für Neurodegenerative Erkrankungen e.V. (DZNE)

All articles from Health and Medicine >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: OLED microdisplays in data glasses for improved human-machine interaction

The Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP has been developing various applications for OLED microdisplays based on organic semiconductors. By integrating the capabilities of an image sensor directly into the microdisplay, eye movements can be recorded by the smart glasses and utilized for guidance and control functions, as one example. The new design will be debuted at Augmented World Expo Europe (AWE) in Berlin at Booth B25, October 18th – 19th.

“Augmented-reality” and “wearables” have become terms we encounter almost daily. Both can make daily life a little simpler and provide valuable assistance for...

Im Focus: Artificial Intelligence Helps in the Discovery of New Materials

With the help of artificial intelligence, chemists from the University of Basel in Switzerland have computed the characteristics of about two million crystals made up of four chemical elements. The researchers were able to identify 90 previously unknown thermodynamically stable crystals that can be regarded as new materials. They report on their findings in the scientific journal Physical Review Letters.

Elpasolite is a glassy, transparent, shiny and soft mineral with a cubic crystal structure. First discovered in El Paso County (Colorado, USA), it can also be...

Im Focus: Complex hardmetal tools out of the 3D printer

For the first time, Fraunhofer IKTS shows additively manufactured hardmetal tools at WorldPM 2016 in Hamburg. Mechanical, chemical as well as a high heat resistance and extreme hardness are required from tools that are used in mechanical and automotive engineering or in plastics and building materials industry. Researchers at the Fraunhofer Institute for Ceramic Technologies and Systems IKTS in Dresden managed the production of complex hardmetal tools via 3D printing in a quality that are in no way inferior to conventionally produced high-performance tools.

Fraunhofer IKTS counts decades of proven expertise in the development of hardmetals. To date, reliable cutting, drilling, pressing and stamping tools made of...

Im Focus: Launch of New Industry Working Group for Process Control in Laser Material Processing

At AKL’16, the International Laser Technology Congress held in May this year, interest in the topic of process control was greater than expected. Appropriately, the event was also used to launch the Industry Working Group for Process Control in Laser Material Processing. The group provides a forum for representatives from industry and research to initiate pre-competitive projects and discuss issues such as standards, potential cost savings and feasibility.

In the age of industry 4.0, laser technology is firmly established within manufacturing. A wide variety of laser techniques – from USP ablation and additive...

Im Focus: New laser joining technologies at ‘K 2016’ trade fair

Every three years, the plastics industry gathers at K, the international trade fair for plastics and rubber in Düsseldorf. The Fraunhofer Institute for Laser Technology ILT will also be attending again and presenting many innovative technologies, such as for joining plastics and metals using ultrashort pulse lasers. From October 19 to 26, you can find the Fraunhofer ILT at the joint Fraunhofer booth SC01 in Hall 7.

K is the world’s largest trade fair for the plastics and rubber industry. As in previous years, the organizers are expecting 3,000 exhibitors and more than...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

Experts from industry and academia discuss the future mobile telecommunications standard 5G

23.09.2016 | Event News

ICPE in Graz for the seventh time

20.09.2016 | Event News

Using mathematical models to understand our brain

16.09.2016 | Event News

 
Latest News

Chains of nanogold – forged with atomic precision

23.09.2016 | Life Sciences

New leukemia treatment offers hope

23.09.2016 | Health and Medicine

Self-assembled nanostructures hit their target

23.09.2016 | Life Sciences

VideoLinks
B2B-VideoLinks
More VideoLinks >>>