Technique Reveals Structure of Printable Electronics
Printable electronics are created by spraying or printing inks containing conductive organic molecules onto a surface. The process is fast and much less expensive than current production techniques for items like solar cells or computer and television displays.
Additionally, it holds potential for amazing new applications: picture a wearable interactive display that needs no batteries. In the solar industry, the ability to print solar cells on giant roll-to-roll printing presses – like printing a newspaper – could make the technology much more affordable and mass marketable.
NC State physicists Dr. Harald Ade and Dr. Brian Collins, in collaboration with Dr. Michael Chabinyc at the University of California Santa Barbara, wanted to know why some processing steps resulted in better and more efficient devices than others. “Manufacturers know that some materials work better than others in these devices, but it’s essentially still a process of trial and error,” Ade says. “We wanted to give them a way to characterize these materials so that they could see what they had and why it was working.”
To do that, Collins and Ade went to Lawrence Berkeley National Laboratory’s Advanced Light Source (ALS). They developed a new technique which used the powerful X-rays from the ALS to look at how individual molecules within these materials organize. They found that the best performing devices were characterized by particular molecular alignments within the materials.
“In transistors, we found that as the alignment between molecules increased, so did the performance,” Collins says. “In the case of the solar cells, we discovered alignment of molecules at interfaces in the device, which may be the key to more efficient harvesting of light. For both, this was the first time anyone had been able to really look at what was happening at the molecular level.”
The researchers’ results appear in the journal Nature Materials. Led by NC State and UCSB, an international collaboration of researchers from Lawrence Berkeley National Laboratory, Monash University in Australia, and University Erlangen-Nuremberg in Germany contributed to the work.
“We’re hoping that this technique will give researchers and manufacturers greater insight into the fundamentals of these materials,” Collins says. “Understanding how these materials work can only lead to improved performance and better commercial viability.”
The research was funded by the Department of Energy, National Science Foundation through the American Reinvestment and Recovery Act, and Department of Education. The Advanced Light Source is supported by the Director, Office of Science, Office of Basic Energy Sciences, of the U.S. Department of Energy.
-peake-
Note to editors: Abstract follows.
“Polarized X-ray scattering reveals non-crystalline orientational ordering in organic films”
Authors: B. A. Collins, H. Yan, E. Gann, H. Ade, North Carolina State University; J. E. Cochran, M. L. Chabinyc, University of California, Santa Barbara; C. Hub, R. Fink, Physikalische Chemie and ICMM, University Erlangen-Nuremberg, Erlangen, Germany; C.Wang, Advanced Light Source, Lawrence Berkeley National Laboratory; T. Schuettfort, University of Cambridge, U.K.; C. R. McNeill, Monash University, Victoria, Australia
Published: April 15th 2012 in Nature Materials
Abstract:
Molecular orientation critically influences the mechanical, chemical, optical and electronic properties of organic materials. So far, molecular-scale ordering in soft matter could be characterized with X-ray or electron microscopy techniques only if the sample exhibited sufficient crystallinity. Here, we show that the resonant scattering of polarized soft X-rays (P-SoXS) by molecular orbitals is not limited by crystallinity and that it can be used to probe molecular orientation down to size scales of 10 nm. We first apply the technique on highly crystalline small-molecule thin films and subsequently use its high sensitivity to probe the impact of liquid-crystalline ordering on charge mobility in polymeric transistors. P-SoXS also reveals scattering anisotropy in amorphous domains of all-polymer organic solar cells where interfacial interactions pattern orientational alignment in the matrix phase, which probably plays an important role in the photophysics. The energy and q-dependence of the scattering anisotropy allows the identification of the composition and the degree of orientational order in the domains.
Media Contact
More Information:
http://www.ncsu.eduAll latest news from the category: Materials Sciences
Materials management deals with the research, development, manufacturing and processing of raw and industrial materials. Key aspects here are biological and medical issues, which play an increasingly important role in this field.
innovations-report offers in-depth articles related to the development and application of materials and the structure and properties of new materials.
Newest articles

Using Electroencephalography to Improve Language Disorder Treatments
Researchers work towards an inexpensive and portable solution for treating aphasia Electroencephalography (EEG) may offer a more accessible alternative to functional magnetic resonance imaging (fMRI) for guiding transcranial direct current…

Measuring Life on Earth from Space: A Global Research Project
Measurements and data collected from space can be used to better understand life on Earth. An ambitious, multinational research project funded by NASA and co-led by UC Merced civil and…

Best Approach for Stroke in Medium-Sized Blood Vessels Identified
Calgary’s Stroke Program advancing science to improve care, treatment and outcomes for patients University of Calgary’s Hotchkiss Brain Institute researchers with the Calgary Stroke Program at Foothills Medical Centre revolutionized…