Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Using Powder-Free Latex Gloves Reduces Latex Allergy Rate in Health Care Workers

18.08.2011
Airborne latex allergens spread by cornstarch used to powder gloves

Researchers at The Medical College of Wisconsin investigating latex allergy in health care workers have demonstrated the most effective public health strategy to prevent allergic sensitization is by stopping the use of powdered latex gloves.

Previous medical studies pointed out this association of latex allergy to powdered latex glove use but were not able to completely confirm this link in specific workers. Reducing the use of powdered gloves reduced the allergen in the air and in air ducts at two hospitals, and prevented sensitization to latex in health care workers at both institutions.

These findings, detailed in the paper “Prevention of IgE Sensitization to Latex in Health Care Workers after Reduction of Antigen Exposures,” are published online-first in the August 2011 Journal of Occupational and Environmental Medicine. The CDC quoted this article in its publication Science Clips as one of the best scientific articles of the week, because of the practical way in which the institutions were able to implement and then prove with the study an effective public health strategy.

Kevin J. Kelly, MD, professor of pediatrics (allergy/immunology), internal medicine, and vice chair in pediatrics at the Medical College, is the lead author on the paper.

Dr. Kelly and his colleagues studied more than 800 health care workers at Froedtert Hospital and Children’s Hospital of Wisconsin over a 4.5 year period. Researchers tested the amount of latex allergen in the air ducts of the employees’ primary work areas before and after both institutions switched to powder-free gloves, and found a significant correlation between high levels of airborne allergen and health care workers with a latex allergy, or sensitivity.

The switch to powder-free gloves led to significant changes at both hospitals. The unique study design allowed the investigators to determine that there was a 16-fold reduction in the rate of latex sensitization among the study participants. Among the health care workers who were sensitized to latex at the beginning of the study, 25 percent lost that sensitivity, and are no longer considered sensitized to latex. Whether these fortunate workers will re-develop latex sensitization if exposed to latex in the future is unknown.

“This study provides the strongest evidence that allergic sensitivity to latex in health care workers is linked to airborne allergen exposure through powdered gloves,” Dr. Kelly said. “I believe these findings provide a roadmap for health care institutions that will help minimize the risks of latex sensitization to health care workers. I am extremely grateful to hospital administration at both Froedtert and Children’s for allowing such an intrusive change in health care workers’ daily activities to conduct this study.”

Dr. Kelly’s team also found health care workers who had demonstrated latex sensitization were nearly three times more likely to leave their jobs. This phenomenon has been termed “the healthy survivor” effect and helps explain why there may be an artificial reduction in latex allergy seen in some studies as the effected workers choose to no longer be employed without receiving worker’s compensation from a work related exposure.

The study was supported by a grant from the Centers for Disease Control and Prevention’s National Institute for Occupational Safety and Health.

Other study authors include Mei Lin Wang, MD, MPH and Edward L. Petsonk, MD, National Institute for Occupational Safety and Health; and Meribeth Klancnik, Medical College of Wisconsin.

Maureen Mack | EurekAlert!
Further information:
http://www.mcw.edu

More articles from Health and Medicine:

nachricht Organ-on-a-chip mimics heart's biomechanical properties
23.02.2017 | Vanderbilt University

nachricht Researchers identify cause of hereditary skeletal muscle disorder
22.02.2017 | Klinikum der Universität München

All articles from Health and Medicine >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: Safe glide at total engine failure with ELA-inside

On January 15, 2009, Chesley B. Sullenberger was celebrated world-wide: after the two engines had failed due to bird strike, he and his flight crew succeeded after a glide flight with an Airbus A320 in ditching on the Hudson River. All 155 people on board were saved.

On January 15, 2009, Chesley B. Sullenberger was celebrated world-wide: after the two engines had failed due to bird strike, he and his flight crew succeeded...

Im Focus: Breakthrough with a chain of gold atoms

In the field of nanoscience, an international team of physicists with participants from Konstanz has achieved a breakthrough in understanding heat transport

In the field of nanoscience, an international team of physicists with participants from Konstanz has achieved a breakthrough in understanding heat transport

Im Focus: DNA repair: a new letter in the cell alphabet

Results reveal how discoveries may be hidden in scientific “blind spots”

Cells need to repair damaged DNA in our genes to prevent the development of cancer and other diseases. Our cells therefore activate and send “repair-proteins”...

Im Focus: Dresdner scientists print tomorrow’s world

The Fraunhofer IWS Dresden and Technische Universität Dresden inaugurated their jointly operated Center for Additive Manufacturing Dresden (AMCD) with a festive ceremony on February 7, 2017. Scientists from various disciplines perform research on materials, additive manufacturing processes and innovative technologies, which build up components in a layer by layer process. This technology opens up new horizons for component design and combinations of functions. For example during fabrication, electrical conductors and sensors are already able to be additively manufactured into components. They provide information about stress conditions of a product during operation.

The 3D-printing technology, or additive manufacturing as it is often called, has long made the step out of scientific research laboratories into industrial...

Im Focus: Mimicking nature's cellular architectures via 3-D printing

Research offers new level of control over the structure of 3-D printed materials

Nature does amazing things with limited design materials. Grass, for example, can support its own weight, resist strong wind loads, and recover after being...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

Booth and panel discussion – The Lindau Nobel Laureate Meetings at the AAAS 2017 Annual Meeting

13.02.2017 | Event News

Complex Loading versus Hidden Reserves

10.02.2017 | Event News

International Conference on Crystal Growth in Freiburg

09.02.2017 | Event News

 
Latest News

New pop-up strategy inspired by cuts, not folds

27.02.2017 | Materials Sciences

Sandia uses confined nanoparticles to improve hydrogen storage materials performance

27.02.2017 | Interdisciplinary Research

Decoding the genome's cryptic language

27.02.2017 | Life Sciences

VideoLinks
B2B-VideoLinks
More VideoLinks >>>