Global warming leads to more precipitation as warmer air holds more moisture – hence earlier research suggested the Antarctic ice sheet might grow under climate change. Now a study published in Nature shows that a lot of the ice gain due to increased snowfall is countered by an acceleration of ice-flow to the ocean. Thus Antarctica’s contribution to global sea-level rise is probably greater than hitherto estimated, the team of authors from the Potsdam Institute for Climate Impact Research (PIK) concludes.
“Between 30 and 65 percent of the ice gain due to enhanced snowfall in Antarctica is countervailed by enhanced ice loss along the coastline,” says lead-author Ricarda Winkelmann. For the first time, an ensemble of ice-physics simulations shows that future ice discharge is increased up to three times because of additional precipitation in Antarctica under global warming. “The effect exceeds that of surface warming as well as that of basal ice-shelf melting,” Winkelmann says.
During the last decade, the Antarctic ice-sheet has lost volume at a rate comparable to that of Greenland. “The one certainty we have about Antarctica under global warming is that snowfall will increase,” Winkelmann explains. “Since surface melt might remain comparably small even under strong global warming, because Antarctica will still be a pretty chilly place, the big question is: How much more mass within the ice sheet will slowly but inexorably flow off Antarctica and contribute to sea-level rise, which is one of the major impacts of climate change.”
Since snowfall on the ice masses of Antarctica takes water out of the global water cycle, the continent’s net contribution to sea-level rise could be negative during the next 100 years – this is what a number of global and regional models suggest. The new findings indicate that this effect to a large extent is offset by changes in the ice-flow dynamics. Snow piling up on the ice is heavy and hence exerts pressure – the higher the ice the more pressure. Because additional snowfall elevates the grounded ice-sheet but less so the floating ice shelves, it flows more rapidly towards the coast of Antarctica where it eventually breaks off into icebergs and elevates sea level.
A number of processes are relevant for ice-loss in Antarctica, most notably to sub-shelf melting caused by warming of the surrounding ocean water. These phenomena explain the already observed contribution to sea-level rise.
“We now know that snowfall in Antarctica will not save us from sea-level rise,” says second author Anders Levermann, research domain co-chair at PIK and a lead author of the sea-level change chapter of the upcoming IPCC’s 5th assessment report. “Sea level is rising – that is a fact. Now we need to understand how quickly we have to adapt our coastal infrastructure; and that depends on how much CO2 we keep emitting into the atmosphere,” Levermann concludes.
Article: Winkelmann, R., Levermann, A., Martin, M.A., Frieler, K. (2012): Increased future ice discharge from Antarctica owing to higher snowfall. Nature [doi:10.1038/nature11616]For further information please contact:
Jonas Viering | PIK Potsdam
Tracking the amount of sea ice from the Greenland ice sheet
28.09.2016 | Ca' Foscari University of Venice
A perfect sun-storm
28.09.2016 | Helmholtz-Zentrum Potsdam - Deutsches GeoForschungsZentrum GFZ
Friction stir welding is a still-young and thus often unfamiliar pressure welding process for joining flat components and semi-finished components made of light metals.
Scientists at the University of Stuttgart have now developed two new process variants that will considerably expand the areas of application for friction stir welding.
Technologie-Lizenz-Büro (TLB) GmbH supports the University of Stuttgart in patenting and marketing its innovations.
Friction stir welding is a still-young and thus often unfamiliar pressure welding process for joining flat components and semi-finished components made of...
Optical quantum computers can revolutionize computer technology. A team of researchers led by scientists from Münster University and KIT now succeeded in putting a quantum optical experimental set-up onto a chip. In doing so, they have met one of the requirements for making it possible to use photonic circuits for optical quantum computers.
Optical quantum computers are what people are pinning their hopes on for tomorrow’s computer technology – whether for tap-proof data encryption, ultrafast...
The Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP has been developing various applications for OLED microdisplays based on organic semiconductors. By integrating the capabilities of an image sensor directly into the microdisplay, eye movements can be recorded by the smart glasses and utilized for guidance and control functions, as one example. The new design will be debuted at Augmented World Expo Europe (AWE) in Berlin at Booth B25, October 18th – 19th.
“Augmented-reality” and “wearables” have become terms we encounter almost daily. Both can make daily life a little simpler and provide valuable assistance for...
With the help of artificial intelligence, chemists from the University of Basel in Switzerland have computed the characteristics of about two million crystals made up of four chemical elements. The researchers were able to identify 90 previously unknown thermodynamically stable crystals that can be regarded as new materials. They report on their findings in the scientific journal Physical Review Letters.
Elpasolite is a glassy, transparent, shiny and soft mineral with a cubic crystal structure. First discovered in El Paso County (Colorado, USA), it can also be...
For the first time, Fraunhofer IKTS shows additively manufactured hardmetal tools at WorldPM 2016 in Hamburg. Mechanical, chemical as well as a high heat resistance and extreme hardness are required from tools that are used in mechanical and automotive engineering or in plastics and building materials industry. Researchers at the Fraunhofer Institute for Ceramic Technologies and Systems IKTS in Dresden managed the production of complex hardmetal tools via 3D printing in a quality that are in no way inferior to conventionally produced high-performance tools.
Fraunhofer IKTS counts decades of proven expertise in the development of hardmetals. To date, reliable cutting, drilling, pressing and stamping tools made of...
28.09.2016 | Event News
27.09.2016 | Event News
23.09.2016 | Event News
28.09.2016 | Medical Engineering
28.09.2016 | Materials Sciences
28.09.2016 | Business and Finance