Columbus hatch closed for last time
Preparations of the European Columbus laboratory took an important step earlier this week with the final closure of the module’s hatch ahead of the December launch to the International Space Station.
Although there was no formal ceremony to mark the occasion, the hatch closure is an important milestone for all involved. “This means we are 99% ready for flight,” explains Bernardo Patti, ESA’s Columbus Project Manager. “All the activities related to the pressurised volume are finished. The work left to be done on the exterior is considered to be minor.”
The 8-metre long Columbus laboratory is currently under preparation for flight at the Space Station Processing Facility (SSPF) at NASA’s Kennedy Space Center (KSC), in Florida.
The team at KSC has worked hard over the past weeks to meet the schedule. “The last checkouts were completed - the module worked perfectly and all the health checks were successful,” says Patti.
After power shutdown the team performed a meticulous check of each zone inside the module. The hatch was then closed to 80%, leaving a gap to allow for final air purge, before being fully closed late on Tuesday afternoon. Patti: “The next time the hatch is opened will be in orbit, allowing the astronauts to enter the module for the very first time.”
Next up for Columbus is a Payload Readiness Review which is expected to give the green light for moving the module to the canister – a large container in which Columbus will be taken to the launch pad early in November ready to be placed inside the Space Shuttle’s cargo bay.
The European Columbus laboratory is the cornerstone of ESA’s contribution to the ISS and the first European laboratory dedicated to long-term research in space. Columbus will be carried into orbit in the cargo bay of Space Shuttle Atlantis on the STS-122 mission, scheduled for launch on 6 December 2007.
The STS-122 crew includes ESA astronauts Hans Schlegel and Leopold Eyharts. Eyharts will remain on the ISS for two months as a member of the Expedition 16 crew to oversee the in-orbit commissioning of Columbus and its experimental facilities.
Markus Bauer | alfa
The most recent press releases about innovation >>>
Die letzten 5 Focus-News des innovations-reports im Überblick:
Heatwaves in the Arctic, longer periods of vegetation in Europe, severe floods in West Africa – starting in 2021, scientists want to explore the emissions of the greenhouse gas methane with the German-French satellite MERLIN. This is made possible by a new robust laser system of the Fraunhofer Institute for Laser Technology ILT in Aachen, which achieves unprecedented measurement accuracy.
Methane is primarily the result of the decomposition of organic matter. The gas has a 25 times greater warming potential than carbon dioxide, but is not as...
Hydrogen is regarded as the energy source of the future: It is produced with solar power and can be used to generate heat and electricity in fuel cells. Empa researchers have now succeeded in decoding the movement of hydrogen ions in crystals – a key step towards more efficient energy conversion in the hydrogen industry of tomorrow.
As charge carriers, electrons and ions play the leading role in electrochemical energy storage devices and converters such as batteries and fuel cells. Proton...
Scientists from the Excellence Cluster Universe at the Ludwig-Maximilians-Universität Munich have establised "Cosmowebportal", a unique data centre for cosmological simulations located at the Leibniz Supercomputing Centre (LRZ) of the Bavarian Academy of Sciences. The complete results of a series of large hydrodynamical cosmological simulations are available, with data volumes typically exceeding several hundred terabytes. Scientists worldwide can interactively explore these complex simulations via a web interface and directly access the results.
With current telescopes, scientists can observe our Universe’s galaxies and galaxy clusters and their distribution along an invisible cosmic web. From the...
Temperature measurements possible even on the smallest scale / Molecular ruby for use in material sciences, biology, and medicine
Chemists at Johannes Gutenberg University Mainz (JGU) in cooperation with researchers of the German Federal Institute for Materials Research and Testing (BAM)...
Germany counts high-precision manufacturing processes among its advantages as a location. It’s not just the aerospace and automotive industries that require almost waste-free, high-precision manufacturing to provide an efficient way of testing the shape and orientation tolerances of products. Since current inline measurement technology not yet provides the required accuracy, the Fraunhofer Institute for Laser Technology ILT is collaborating with four renowned industry partners in the INSPIRE project to develop inline sensors with a new accuracy class. Funded by the German Federal Ministry of Education and Research (BMBF), the project is scheduled to run until the end of 2019.
New Manufacturing Technologies for New Products