New reactor puts hydrogen from renewable fuels within reach
The first reactor capable of producing hydrogen from a renewable fuel source–ethanol–efficiently enough to hold economic potential has been invented by University of Minnesota engineers. When coupled with a hydrogen fuel cell, the unit–small enough to hold in your hand–could generate one kilowatt of power, almost enough to supply an average home, the researchers said. The technology is poised to remove the major stumbling block to the “hydrogen economy”: no free hydrogen exists, except what is made at high cost from fossil fuels. The work will be published in the Feb. 13 issue of Science.
The researchers see an early use for their invention in remote areas, where the installation of new power lines is not feasible. People could buy ethanol and use it to power small hydrogen fuel cells in their basements. The process could also be extended to biodiesel fuels, the researchers said. Its benefits include reducing dependence on imported fuels, reducing carbon dioxide emissions (because the carbon dioxide produced by the reaction is stored in the next years corn crop) and boosting rural economies.
Hydrogen is now produced exclusively by a process called steam reforming, which requires very high temperatures and large furnaces–in other words, a huge input of energy. Its unsuitable for any application except large-scale refineries, said Lanny Schmidt, Regents Professor of Chemical Engineering, who led the effort. Working with him were scientist Gregg Deluga, first author of the Science paper, and graduate student James Salge. All three are in the universitys department of chemical engineering and materials science.
“The hydrogen economy means cars and electricity powered by hydrogen,” said Schmidt. “But hydrogen is hard to come by. You cant pipe it long distances. There are a few hydrogen fueling stations, but they strip hydrogen from methane–natural gas–on site. Its expensive, and because it uses fossil fuels, it increases carbon dioxide emissions, so this is only a short-term solution until renewable hydrogen is available.”
Ethanol is easy to transport and relatively nontoxic. It is already being produced from corn and used in car engines. But if it were used instead to produce hydrogen for a fuel cell, the whole process would be nearly three times as efficient. That is, a bushel of corn would yield three times as much power if its energy were channeled into hydrogen fuel cells rather than burned along with gasoline.
“We can potentially capture 50 percent of the energy stored in sugar [in corn], whereas converting the sugar to ethanol and burning the ethanol in a car would harvest only 20 percent of the energy in sugar,” said Schmidt. “Ethanol in car engines is burned with 20 percent efficiency, but if you used ethanol to make hydrogen for a fuel cell, you would get 60 percent efficiency.”
The difference, Deluga explained, is due in large part to the need to remove all the water from ethanol before it can be put in an automobile gas tank–and the last drops of water are the hardest to remove. But the new process doesnt require pure ethanol; in fact, it strips hydrogen from both ethanol and water, yielding a hydrogen bonus.
The invention rests on two innovations: a catalyst based on the metals rhodium and ceria, and an automotive fuel injector that vaporizes and mixes the ethanol-water fuel. The vaporized fuel mixture is injected into a tube that contains a porous plug made from rhodium and ceria. The fuel mixture passes through the plug and emerges as a mixture of hydrogen, carbon dioxide and minor products. The reaction takes only 50 milliseconds and eliminates the flames and soot that commonly accompany ethanol combustion.
In a typical ethanol-water fuel mixture, one could ideally get five molecules of hydrogen for each molecule of ethanol. Reacting ethanol alone would yield three hydrogen molecules. So far, the Schmidt team has harvested four hydrogen molecules per ethanol molecule.
“Were confident we can improve this technology to increase the yield of hydrogen and use it to power a workable fuel cell,” said Salge.
The work was supported by the University of Minnesotas Initiative on Renewable Energy and the Environment, the National Science Foundation and the U.S. Department of Energy.
Embargoed by Science until 2 p.m. Eastern time (1 p.m. Central) Thursday, Feb. 12. For a copy of the paper, call 202-326-6440 or e-mail email@example.com.
Lanny Schmidt, 612-625-9391
Gregg Deluga, 612-625-6083
James Salge, 612-625-6073
Deane Morrison, University News Service, 612-624-2346 (Feb. 9-10 and after Feb. 15)
Patty Mattern, University News Service, 612-624-0214 (Feb. 11-15)
Alle Nachrichten aus der Kategorie: Power and Electrical Engineering
This topic covers issues related to energy generation, conversion, transportation and consumption and how the industry is addressing the challenge of energy efficiency in general.
innovations-report provides in-depth and informative reports and articles on subjects ranging from wind energy, fuel cell technology, solar energy, geothermal energy, petroleum, gas, nuclear engineering, alternative energy and energy efficiency to fusion, hydrogen and superconductor technologies.
3D printing the first ever biomimetic tongue surface
Scientists have created synthetic soft surfaces with tongue-like textures for the first time using 3D printing, opening new possibilities for testing oral processing properties of food, nutritional technologies, pharmaceutics and…