Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Vega upper composite passes tests at ESTEC

09.10.2006
The upper composite of ESA’s new small launcher has passed its vibration tests at ESA's European Space Research and Technology Centre (ESTEC) with flying colours. Vega’s components are built and tested at various locations across Europe. The first launch is planned for the end of 2007 from Europe’s Spaceport in Kourou, French Guiana.
Vega, which is being built by European industry under the leadership of ELV SpA (Italy), is a small launch vehicle designed to carry payloads in the range 300 kg to 2.5 tonnes into low Earth orbits. The typical reference for Vega’s launch capacity is to carry 1500 kg to a 700 km-altitude polar orbit. Vega will be particularly suitable for the launch of scientific and Earth observation missions.

Vibrations

During the launch of a rocket, vibrations occur due to engine ignition, the thrust of the engines and the high-speed flow of air over the body of the vehicle as it accelerates through the Earth’s atmosphere.

The upper composite that has just been tested is the top part of the launcher, which houses the navigation, communications and control equipment. The payload is carried on top of the composite, protected by a streamlined fairing, or nosecone. During testing, a mechanically representative model of a real satellite was used.

In order to confirm that the upper composite will be able to withstand the vibrations that it will experience during launch, it was mounted on the ‘multi-shaker’ in the Test Centre at ESTEC. This electrodynamic vibration table applied accelerations to the base of the composite while around 400 accelerometers and 40 strain gauges measured the movements and forces within the structure. This confirms that the design calculations are correct.

“The vibration tests went well and we are on schedule” said Vega Test Manager Wolfgang Teichert. “We have carried out most of the tests for the final stage of the launcher”.

Final exam

At the end of 2006, reports on all the tests will be presented at the ‘Critical Design Review’. If Vega passes this ‘final exam’, production of components for the qualification flight launcher can proceed.

Industry day

The fourth Vega industry day is taking place on Thursday 5 October 2006 at ESA-ESTEC and the adjacent Space Expo in Noordwijk, The Netherlands. All the space industry members committed to the Vega Small Launcher programme are involved. The industry day is an occasion for all participants in the Vega programme to share an overview of the key technical and programmatic achievements in the development activities being carried out under the responsibility of the three main industrial contractors for the Vega programme:
- Vitrociset SpA (Italy) – ground segment
- Europropulsion SA (France/Italy) – solid propellant motor and P80 first stage
- ELV SpA (Italy) – launch vehicle
It will also be an opportunity to focus on the upcoming programme milestones leading to the qualification flight. Later flights, planned in the context of the Vega Research and Technology Accompaniment (VERTA) programme, will also be discussed. VERTA includes support for five demonstration flights that will serve to launch selected ESA payloads and showcase Vega’s capabilities.

Miguel Lopez | EurekAlert!
Further information:
http://www.esa.int

More articles from Physics and Astronomy:

nachricht From rocks in Colorado, evidence of a 'chaotic solar system'
23.02.2017 | University of Wisconsin-Madison

nachricht Prediction: More gas-giants will be found orbiting Sun-like stars
22.02.2017 | Carnegie Institution for Science

All articles from Physics and Astronomy >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: Safe glide at total engine failure with ELA-inside

On January 15, 2009, Chesley B. Sullenberger was celebrated world-wide: after the two engines had failed due to bird strike, he and his flight crew succeeded after a glide flight with an Airbus A320 in ditching on the Hudson River. All 155 people on board were saved.

On January 15, 2009, Chesley B. Sullenberger was celebrated world-wide: after the two engines had failed due to bird strike, he and his flight crew succeeded...

Im Focus: Breakthrough with a chain of gold atoms

In the field of nanoscience, an international team of physicists with participants from Konstanz has achieved a breakthrough in understanding heat transport

In the field of nanoscience, an international team of physicists with participants from Konstanz has achieved a breakthrough in understanding heat transport

Im Focus: DNA repair: a new letter in the cell alphabet

Results reveal how discoveries may be hidden in scientific “blind spots”

Cells need to repair damaged DNA in our genes to prevent the development of cancer and other diseases. Our cells therefore activate and send “repair-proteins”...

Im Focus: Dresdner scientists print tomorrow’s world

The Fraunhofer IWS Dresden and Technische Universität Dresden inaugurated their jointly operated Center for Additive Manufacturing Dresden (AMCD) with a festive ceremony on February 7, 2017. Scientists from various disciplines perform research on materials, additive manufacturing processes and innovative technologies, which build up components in a layer by layer process. This technology opens up new horizons for component design and combinations of functions. For example during fabrication, electrical conductors and sensors are already able to be additively manufactured into components. They provide information about stress conditions of a product during operation.

The 3D-printing technology, or additive manufacturing as it is often called, has long made the step out of scientific research laboratories into industrial...

Im Focus: Mimicking nature's cellular architectures via 3-D printing

Research offers new level of control over the structure of 3-D printed materials

Nature does amazing things with limited design materials. Grass, for example, can support its own weight, resist strong wind loads, and recover after being...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

Booth and panel discussion – The Lindau Nobel Laureate Meetings at the AAAS 2017 Annual Meeting

13.02.2017 | Event News

Complex Loading versus Hidden Reserves

10.02.2017 | Event News

International Conference on Crystal Growth in Freiburg

09.02.2017 | Event News

 
Latest News

New pop-up strategy inspired by cuts, not folds

27.02.2017 | Materials Sciences

Sandia uses confined nanoparticles to improve hydrogen storage materials performance

27.02.2017 | Interdisciplinary Research

Decoding the genome's cryptic language

27.02.2017 | Life Sciences

VideoLinks
B2B-VideoLinks
More VideoLinks >>>