The problem: the manufacturing techniques required to make quantum devices have been equally exotic.
That is, until now.
Researchers at Ohio State University have discovered a way to make quantum devices using technology common to the chip-making industry today.
This work might one day enable faster, low-power computer chips. It could also lead to high-resolution cameras for security and public safety, and cameras that provide clear vision through bad weather.
Paul Berger, professor of electrical and computer engineering and professor of physics at Ohio State University, and his colleagues report their findings in an upcoming issue of IEEE Electron Device Letters.
The team fabricated a device called a tunneling diode using the most common chip-making technique, called chemical vapor deposition.
“We wanted to do this using only the tools found in the typical chip-makers toolbox,” Berger said. “Here we have a technique that manufacturers could potentially use to fabricate quantum devices directly on a silicon chip, side-by-side with their regular circuits and switches.”
The quantum device in question is a resonant interband tunneling diode (RITD) -- a device that enables large amounts of current to be regulated through a circuit, but at very low voltages. That means that such devices run on very little power.
RITDs have been difficult to manufacture because they contain dopants -- chemical elements -- that don’t easily fit within a silicon crystal.
Atoms of the RITD dopants antimony or phosphorus, for example, are large compared to atoms of silicon. Because they don’t fit into the natural openings inside a silicon crystal, the dopants tend to collect on the surface of a chip.
“It’s like when you’re playing Tetris and you have a big block raining down, and only a small square to fit it in. The block has to sit on top,” Berger said. “When you’re building up layers of silicon, these dopants don’t readily fit in. Eventually, they clump together on top of the chip.”
In the past, researchers have tried adding the dopants while growing the silicon wafer one crystal layer at a time -- using a slow and expensive process called molecular beam epitaxy, a method which is challenging for high-volume manufacturing. That process also creates too many defects within the silicon.
Berger discovered that RITD dopants could be added during chemical vapor deposition, in which a gas carries the chemical elements to the surface of a wafer many layers at a time. The key was determining the right reactor conditions to deliver the dopants to the silicon, he found.
“One key is hydrogen,” he said. “It binds to the silicon surface and keeps the dopants from clumping. So you don’t have to grow chips at 320 degrees Celsius [approximately 600 degrees Fahrenheit] like you do when using molecular beam epitaxy. You can actually grow them at a higher temperature like 600 degrees Celsius [more than 1100 degrees Fahrenheit] at a lower cost, and with fewer crystal defects.”
Tunneling diodes are so named because they exploit a quantum mechanical effect known as tunneling, which lets electrons pass through thin barriers unhindered.
In theory, interband tunneling diodes could form very dense, very efficient micro-circuits in computer chips. A large amount of data could be stored in a small area on a chip with very little energy required.
Researchers judge the usefulness of tunneling diodes by the abrupt change in the current densities they carry, a characteristic known as “peak-to-valley ratio.” Different ratios are appropriate for different kinds of devices. Logic circuits such as those on a computer chip are best suited by a ratio of about 2.
The RITDs that Berger’s team fabricated had a ratio of 1.85.
“We’re close, and I’m sure we can do better,” he said.
He envisions his RITDs being used for ultra-low-power computer chips operating with small voltages and producing less wasted heat.
“Chip makers today are having a great difficulty boosting performance in each generation, so they pack chips with more and more circuitry, and end up generating a lot of heat,” Berger said. “That’s why a laptop computer is often too hot to actually sit atop your lap. Soon, their heat output will rival that of a nuclear reactor per unit volume.”
“That’s why moving to quantum devices will be a game-changer.”
RITDs could form high-resolution detectors for imaging devices called focal plane arrays. These arrays operate at wavelengths beyond the human eye and can permit detection of concealed weapons and improvised explosive devices. They can also provide vision through rain, snow, fog, and even mild dust storms, for improved airplane and automobile safety, Berger said. Medical imaging of cancerous tumors is another potential application.
His coauthors on the paper included Si-Young Park, and R. Anisha, both doctoral students in electrical engineering at Ohio State; and Roger Loo, Ngoc Duy Nguyen, Shotaro Takeuchi, and Matty Caymax, all of IMEC, an industrial research center in Belgium.
This work was partially supported by the National Science Foundation.
Contact: Paul R. Berger, (614) 247-6235; email@example.com
Pam Frost Gorder | Newswise Science News
Seeing the quantum future... literally
16.01.2017 | University of Sydney
Airborne thermometer to measure Arctic temperatures
11.01.2017 | Moscow Institute of Physics and Technology
Among the general public, solar thermal energy is currently associated with dark blue, rectangular collectors on building roofs. Technologies are needed for aesthetically high quality architecture which offer the architect more room for manoeuvre when it comes to low- and plus-energy buildings. With the “ArKol” project, researchers at Fraunhofer ISE together with partners are currently developing two façade collectors for solar thermal energy generation, which permit a high degree of design flexibility: a strip collector for opaque façade sections and a solar thermal blind for transparent sections. The current state of the two developments will be presented at the BAU 2017 trade fair.
As part of the “ArKol – development of architecturally highly integrated façade collectors with heat pipes” project, Fraunhofer ISE together with its partners...
At TU Wien, an alternative for resource intensive formwork for the construction of concrete domes was developed. It is now used in a test dome for the Austrian Federal Railways Infrastructure (ÖBB Infrastruktur).
Concrete shells are efficient structures, but not very resource efficient. The formwork for the construction of concrete domes alone requires a high amount of...
Many pathogens use certain sugar compounds from their host to help conceal themselves against the immune system. Scientists at the University of Bonn have now, in cooperation with researchers at the University of York in the United Kingdom, analyzed the dynamics of a bacterial molecule that is involved in this process. They demonstrate that the protein grabs onto the sugar molecule with a Pac Man-like chewing motion and holds it until it can be used. Their results could help design therapeutics that could make the protein poorer at grabbing and holding and hence compromise the pathogen in the host. The study has now been published in “Biophysical Journal”.
The cells of the mouth, nose and intestinal mucosa produce large quantities of a chemical called sialic acid. Many bacteria possess a special transport system...
UMD, NOAA collaboration demonstrates suitability of in-orbit datasets for weather satellite calibration
"Traffic and weather, together on the hour!" blasts your local radio station, while your smartphone knows the weather halfway across the world. A network of...
Fiber-reinforced plastics (FRP) are frequently used in the aeronautic and automobile industry. However, the repair of workpieces made of these composite materials is often less profitable than exchanging the part. In order to increase the lifetime of FRP parts and to make them more eco-efficient, the Laser Zentrum Hannover e.V. (LZH) and the Apodius GmbH want to combine a new measuring device for fiber layer orientation with an innovative laser-based repair process.
Defects in FRP pieces may be production or operation-related. Whether or not repair is cost-effective depends on the geometry of the defective area, the tools...
10.01.2017 | Event News
09.01.2017 | Event News
05.01.2017 | Event News
16.01.2017 | Power and Electrical Engineering
16.01.2017 | Information Technology
16.01.2017 | Power and Electrical Engineering