Direct measurement of the formation length of photons
How long does it take an electron to form a photon? The answer would normally be: so short a time that it cannot be measured. However, the international CERN team responsible for experiment NA63 – mainly staffed by physicists from Aarhus University – has now succeeded in dragging out the process, thereby making it measurable.
They achieved this by utilising the phenomena of objects moving slower and shortening in length from Einstein’s theory of relativity, along with two pieces of gold foil and a micrometre screw.
In Niels Bohr’s atom model, electrons orbit around the nucleus in ‘shells’ – the so-called stationary states. Light is emitted by a quantum leap between a high-lying shell and one nearer the nucleus. However, it is impossible to find the electron between the two shells, so it could be thought that the light emission process itself was instantaneous: the electron is in the outer shell and immediately after sending out light, it is in the inner one.
However, Associate Professor Ulrik I. Uggerhøj, PhD student Kristoffer K. Andersen, Aarhus University, and the other NA63 members actually found that it takes the electron a measurable amount of time to emit light.
By letting the electron pass two very flat gold foils stretched out at a distance that can be measured with a precision of a few micrometres, they can ‘force’ the electron to emit shortwave light in a well-defined area. The distance between the foils corresponds to the length taken to form the light.
The results have been published in the journal Physical Review Letters under ‘highlights’.
Read more at http://prl.aps.org/abstract/PRL/v108/i7/e071802
and at http://physics.aps.org/synopsis-for/10.1103/PhysRevLett.108.071802
Ulrik I. Uggerhoej | EurekAlert!
The most recent press releases about innovation >>>
Die letzten 5 Focus-News des innovations-reports im Überblick:
Among the general public, solar thermal energy is currently associated with dark blue, rectangular collectors on building roofs. Technologies are needed for aesthetically high quality architecture which offer the architect more room for manoeuvre when it comes to low- and plus-energy buildings. With the “ArKol” project, researchers at Fraunhofer ISE together with partners are currently developing two façade collectors for solar thermal energy generation, which permit a high degree of design flexibility: a strip collector for opaque façade sections and a solar thermal blind for transparent sections. The current state of the two developments will be presented at the BAU 2017 trade fair.
As part of the “ArKol – development of architecturally highly integrated façade collectors with heat pipes” project, Fraunhofer ISE together with its partners...
At TU Wien, an alternative for resource intensive formwork for the construction of concrete domes was developed. It is now used in a test dome for the Austrian Federal Railways Infrastructure (ÖBB Infrastruktur).
Concrete shells are efficient structures, but not very resource efficient. The formwork for the construction of concrete domes alone requires a high amount of...
Many pathogens use certain sugar compounds from their host to help conceal themselves against the immune system. Scientists at the University of Bonn have now, in cooperation with researchers at the University of York in the United Kingdom, analyzed the dynamics of a bacterial molecule that is involved in this process. They demonstrate that the protein grabs onto the sugar molecule with a Pac Man-like chewing motion and holds it until it can be used. Their results could help design therapeutics that could make the protein poorer at grabbing and holding and hence compromise the pathogen in the host. The study has now been published in “Biophysical Journal”.
The cells of the mouth, nose and intestinal mucosa produce large quantities of a chemical called sialic acid. Many bacteria possess a special transport system...
UMD, NOAA collaboration demonstrates suitability of in-orbit datasets for weather satellite calibration
"Traffic and weather, together on the hour!" blasts your local radio station, while your smartphone knows the weather halfway across the world. A network of...
Fiber-reinforced plastics (FRP) are frequently used in the aeronautic and automobile industry. However, the repair of workpieces made of these composite materials is often less profitable than exchanging the part. In order to increase the lifetime of FRP parts and to make them more eco-efficient, the Laser Zentrum Hannover e.V. (LZH) and the Apodius GmbH want to combine a new measuring device for fiber layer orientation with an innovative laser-based repair process.
Defects in FRP pieces may be production or operation-related. Whether or not repair is cost-effective depends on the geometry of the defective area, the tools...