Louis Potters, MD, North Shore-LIJ's chairman of radiation medicine, and his colleagues designed a new program that seeks to improve the quality of complex processes by identifying and removing the causes of errors, and reducing variables that increase the risk of mistakes. North Shore-LIJ has literally adjusted for complex technical challenges in the hardware and software that delivers the radiation by ensuring that nothing is rushed.
Patients do not get on the table until every step is accounted for. "We want to ensure that our patients are safe," said Dr. Potters, who presented the pilot program recently at the American Radium Society Annual Meeting.
Just imagine all the tasks that must be in place before a patient enters the surgical suite, which is a one-time event. Planning for radiation therapy that is delivered daily for weeks requires the efforts of many caregivers, with coordinated handoffs of complex information. It is important that this happens in an aligned and controlled way, and not rushed. The safety program is specifically designed to decrease the risk of errors due to last-minute, and hurried work.
Understanding the risk for error, Dr. Potters identified all the applications that go into delivering the therapy and then set out to use the clinic as a laboratory to understand the processes. He and his colleagues basically mapped the process every step of the way. "The research was necessary to identify the appropriate processes of care, break it down into the eight key components of care and make sure every step is in place before the patient arrives for treatment," Dr. Potters explained. He calls it the "no-fly" policy, because there will be no treatment unless every step is signed off on and ready to go. If everything is not completed on time, the appointment is pushed back.
"The classic culture is not to make patients wait," Dr. Potters said. "But it is more important to have all the stress points in the system running smoothly to ensure minimal risk for the patient."
Dr. Potters and his team looked at the treatment process for 520 cases in the last eight months and measured the time points to see whether the time-to-treat improved over the course of the study. And it did. "We have created this program to help mitigate risk," said Dr. Potters. On average, 10 percent of patient appointments were pushed back. The department went from a culture of 'just in time' to that of 'proactive' recognition of a need to reschedule. And the number of "stops," the times that an appointment had to be re-scheduled because a step in the process was not completed, also went down. During the first month of the study, they had 80 events stopped compared to 20 in the most recent month of the study.
"With complex technologies, resource-compromised staff and pressures to hasten treatment, the use of this process seems to reduce patient safety risks," said Dr. Potters. And the patients are educated about the "no-fly" policy and are more confident that any changes made to the schedule are ultimately done to protect them.
North Shore-LIJ Radiation Medicine Department is the first in the nation to implement such a program for patient safety. "We hope that by spreading the word of how to incorporate better safety processes that other radiation oncology departments will develop similar approaches to enhance cancer care," said Dr. Potters.
Jamie Talan | EurekAlert!
Millions through license revenues
27.04.2017 | Rheinische Friedrich-Wilhelms-Universität Bonn
New High-Performance Center Translational Medical Engineering
26.04.2017 | Fraunhofer ITEM
More and more automobile companies are focusing on body parts made of carbon fiber reinforced plastics (CFRP). However, manufacturing and repair costs must be further reduced in order to make CFRP more economical in use. Together with the Volkswagen AG and five other partners in the project HolQueSt 3D, the Laser Zentrum Hannover e.V. (LZH) has developed laser processes for the automatic trimming, drilling and repair of three-dimensional components.
Automated manufacturing processes are the basis for ultimately establishing the series production of CFRP components. In the project HolQueSt 3D, the LZH has...
Reflecting the structure of composites found in nature and the ancient world, researchers at the University of Illinois at Urbana-Champaign have synthesized thin carbon nanotube (CNT) textiles that exhibit both high electrical conductivity and a level of toughness that is about fifty times higher than copper films, currently used in electronics.
"The structural robustness of thin metal films has significant importance for the reliable operation of smart skin and flexible electronics including...
The nearby, giant radio galaxy M87 hosts a supermassive black hole (BH) and is well-known for its bright jet dominating the spectrum over ten orders of magnitude in frequency. Due to its proximity, jet prominence, and the large black hole mass, M87 is the best laboratory for investigating the formation, acceleration, and collimation of relativistic jets. A research team led by Silke Britzen from the Max Planck Institute for Radio Astronomy in Bonn, Germany, has found strong indication for turbulent processes connecting the accretion disk and the jet of that galaxy providing insights into the longstanding problem of the origin of astrophysical jets.
Supermassive black holes form some of the most enigmatic phenomena in astrophysics. Their enormous energy output is supposed to be generated by the...
The probability to find a certain number of photons inside a laser pulse usually corresponds to a classical distribution of independent events, the so-called...
Microprocessors based on atomically thin materials hold the promise of the evolution of traditional processors as well as new applications in the field of flexible electronics. Now, a TU Wien research team led by Thomas Müller has made a breakthrough in this field as part of an ongoing research project.
Two-dimensional materials, or 2D materials for short, are extremely versatile, although – or often more precisely because – they are made up of just one or a...
28.04.2017 | Event News
20.04.2017 | Event News
18.04.2017 | Event News
28.04.2017 | Medical Engineering
28.04.2017 | Earth Sciences
28.04.2017 | Life Sciences