In a cover article published in Green Chemistry, the research team describes a process that ultimately transforms the lignin byproduct into a thermoplastic – a polymer that becomes pliable above a specific temperature.
Researchers accomplished this by reconstructing larger lignin molecules either through a chemical reaction with formaldehyde or by washing with methanol. Through these simple chemical processes, they created a crosslinked rubber-like material that can also be processed like plastics.
“Our work addresses a pathway to utilize lignin as a sustainable, renewable resource material for synthesis of thermoplastics that are recyclable,” said Naskar, a member of the Department of Energy laboratory’s Material Science and Technology Division.
Instead of using nearly 50 million tons of lignin byproduct produced annually as a low-cost fuel to power paper and pulp mills, the material can be transformed into a lignin-derived high-value plastic. While the lignin byproduct in raw form is worth just pennies a pound as a fuel, the value can potentially increase by a factor of 10 or more after the conversion.
Naskar noted that earlier work on lignin-based plastics utilized material that was available from pulping industries and was a significantly degraded version of native lignin contained in biomass. This decomposition occurs during harsh chemical treatment of biomass.
“Here, however, we attempted to reconstruct larger lignin molecules by a simple crosslinking chemistry and then used it as a substitute for rigid phase in a formulation that behaves like crosslinked rubbers that can also be processed like plastics,” Naskar said.
Crosslinking involves building large lignin molecules by combining smaller molecules where formaldehyde helps to bridge the smaller units by chemical bonding. Naskar envisions the process leading to lower cost gaskets, window channels, irrigation hose, dashboards, car seat foam and a number of other plastic-like products.
A similar material can also be made from lignin produced in biorefineries. The paper, titled “Turning renewable resources into value-added polymer: development of lignin-based thermoplastic,” is available at http://pubs.rsc.org/en/content/articlepdf/2012/gc/c2gc35933b?page=search
Other ORNL authors are Tomonori Saito, Rebecca Brown, Marcus Hunt, Deanna Pickel, Joseph Pickel, Jamie Messman, Frederick Baker and Martin Keller. The research was funded by the Laboratory Directed Research and Development program.
Part of the polymer characterization work was conducted at the Center for Nanophase Materials Sciences, one of the five DOE Nanoscale Science Research Centers supported by the DOE Office of Science, premier national user facilities for interdisciplinary research at the nanoscale. Together the NSRCs comprise a suite of complementary facilities that provide researchers with state-of-the-art capabilities to fabricate, process, characterize and model nanoscale materials, and constitute the largest infrastructure investment of the National Nanotechnology Initiative. The NSRCs are located at DOE's Argonne, Brookhaven, Lawrence Berkeley, Oak Ridge and Sandia and Los Alamos national laboratories. For more information about the DOE NSRCs, please visit http://science.energy.gov/bes/suf/user-facilities/nanoscale-science-research-centers/
UT-Battelle manages ORNL for DOE’s Office of Science. The Office of Science is the single largest supporter of basic research in the physical sciences in the United States and is working to address some of the most pressing challenges of our time. For more information, please visit http://science.energy.gov/.
Ron Walli | Source: Newswise Science News
Further information: www.ornl.gov
Further Reports about: chemical process > green chemistry > high-value plastic > lignin molecules > lignin-based plastics > material science > Materials Science > ORNL > renewable resource > Science TV > synthesis of thermoplastics
More articles from Materials Sciences:
GRAPHENE: Growing Giants
10.12.2013 | American Institute of Physics (AIP)
Polymers can be semimetals
09.12.2013 | Linköping University
Researchers from Brown University and the University of Hawaii have found some mineralogical surprises in the Moon's largest impact crater.
Data from the Moon Mineralogy Mapper that flew aboard India's Chandrayaan-1 lunar orbiter shows a diverse mineralogy in the subsurface of the giant South Pole Aitken basin.
The differing mineral signatures could be reflective of the minerals dredged up at the time of the giant impact 4 billion years ago, ...
In power electronics systems bonded connections create the central electrical connections between adjoining surfaces.
The quality of these bonded connections is one of the main factors that determines the reliability and availability of drive systems in electric vehicles, and hence constitutes a major design challenge for German auto manufacturers aiming to electrify their vehicles.
Now the partners participating in the RoBE (Robust Bonds in ...
International team of scientists develops new feedback method for optimizing the laser pulse shapes used in the control of chemical reactions
In many ways, traditional chemical synthesis is similar to cooking. To alter the final product, you can change the ingredients or their ratio, change the method of mixing ingredients, or change the temperature or pressure of the environment of the ingredients.
Like an accomplished chef, chemists have become very skilled ...
A genetic defect protects mice from infection with influenza viruses
A new study published in the scientific journal PLOS Pathogens points out that mice lacking a protein called Tmprss2 are no longer affected by certain flu viruses.
The discovery was made by researchers from the Helmholtz Centre for Infection Research (HZI) in Braunschweig in collaboration with colleagues from Göttingen and ...
The Light: Global study gets underway with online user survey
Light has a fundamental impact on our sense of well-being and performance. In cooperation with Zumtobel, a supplier of lighting solutions, Fraunhofer IAO has launched a global user survey of lighting quality in offices. The objective is to identify the best lighting conditions for a variety of spaces and lighting ...
10.12.2013 | Physics and Astronomy
10.12.2013 | Agricultural and Forestry Science
10.12.2013 | Power and Electrical Engineering
10.12.2013 | Event News
05.12.2013 | Event News
04.12.2013 | Event News