Sensors used in harsh conditions, such as deep-sea oil wells, must withstand extreme temperatures and pressures for hundreds of hours without failing. Vivek Chidambaram and co-workers at the A*STAR Institute of Microelectronics, Singapore, have investigated two metal alloys that could give micro-electromechanical system (MEMS) sensors better protection in the toughest environments
Typical MEMS sensors measure temperature, pressure or vibration, and they are hermetically sealed inside a strong metal casing to prevent air or moisture degrading the sensors’ electronics. Chidambaram’s team wanted to find cheaper, more durable alternatives to the metal solders, such as gold–tin or copper–tin, which are typically used to seal the case. They tested a 70:30 aluminum–germanium mixture, which has a melting point of about 420 °C. This temperature — the eutectic point — is much lower than that for either metal on its own.
Unlike most conventional packaging materials, aluminum and germanium are compatible with the processes used to manufacture the MEMS. Using the aluminum–germanium sealant should make MEMS manufacturing easier and cheaper, and could also improve the device’s performance, says Chidambaram.
The researchers built a stack of 4 alternating wafers of aluminum and germanium, each less than a micrometer thick, and heated the sandwich under pressure to about 400 °C for 2 hours. Although the wafers did not liquefy, this “thermal aging process facilitated bonding prior to melting,” explains Chidambaram. Raising the temperature to 475 °C for another 2 hours fully melted the mixture, which then formed a strong seal after cooling — a process known as transient liquid-phase bonding.
Next, the researchers used acoustic microscopy, scanning electron microscopy and X-ray spectroscopy to reveal any voids or other defects in the seals. They found that the thermal aging process improved the quality of the seal. Tests showed that it was strong enough to withstand a shear of 46 megapascals — similar to the pressure exerted by almost half a ton per square centimeter — and was impermeable to water. The material lost little of its strength after being exposed to 300 °C for hundreds of hours.
Chidambaram and his team also tested a platinum–indium seal — which has the highest re-melting point (894 °C) of all the solders being considered for these applications — but it lost its strength after long durations at 300 °C, leaving the aluminum–germanium mixture in pole position as a better seal for MEMS. “Cost effectiveness, better thermo-mechanical properties, and its eutectic microstructure makes it an attractive alternative,” says Chidambaram.
The A*STAR-affiliated researchers contributing to this research are from the Institute of Microelectronics
Chidambaram, V., Yeung, H. B. & Shan, G. Development of metallic hermetic sealing for MEMS packaging for harsh environment applications. Journal of Electronic Materials 41, 2256–2266, 2012
Further Reports about: acoustic microscopy > aging process > melting point > MEMS > micro-electromechanical system > Microelectronic > packaging material > scanning electron microscopy > X-ray spectroscopy
More articles from Materials Sciences:
Accelerated corrosion testing of silver provides clues about performance in atmospheric conditions
04.12.2013 | NACE International
New Effect Couples Electricity and Magnetism in Materials
28.11.2013 | Vienna University of Technology
The Light: Global study gets underway with online user survey
Light has a fundamental impact on our sense of well-being and performance. In cooperation with Zumtobel, a supplier of lighting solutions, Fraunhofer IAO has launched a global user survey of lighting quality in offices. The objective is to identify the best lighting conditions for a variety of spaces and lighting ...
Quantum entanglement, a perplexing phenomenon of quantum mechanics that Albert Einstein once referred to as “spooky action at a distance,” could be even spookier than Einstein perceived.
Physicists at the University of Washington and Stony Brook University in New York believe the phenomenon might be intrinsically linked with wormholes, hypothetical features of space-time that in popular science fiction can provide a much-faster-than-light shortcut from one part of the universe to another.
But here’s the catch: One couldn’t actually ...
A star is formed when a large cloud of gas and dust condenses and eventually becomes so dense that it collapses into a ball of gas, where the pressure heats the matter, creating a glowing gas ball – a star is born.
New research from the Niels Bohr Institute, among others, shows that a young, newly formed star in the Milky Way had such an explosive growth, that it was initially about 100 times brighter than it is now. The results are published in the scientific journal, Astrophysical Journal Letters.
The young ...
EPFL scientists have shown how to achieve a dramatic increase in the capacity of optical fibers; Their simple, innovative solution reduces the amount of space required between the pulses of light that transport data
Optical fibers carry data in the form of pulses of light over distances of thousands of miles at amazing speeds. They are one of the glories of modern telecommunications technology.
However, their capacity is limited, because the pulses of light need to be lined up one after the other in ...
NASA's Hurricane and Severe Storms Sentinel airborne mission known as HS3 wrapped up for the 2013 Atlantic Ocean hurricane season at the end of September, and had several highlights. HS3 will return to NASA’s Wallops Flight Facility in Wallops Island, Va., for the 2014 Atlantic hurricane season.
During the 2013 mission, two unmanned Global Hawks flew from Wallops for the first time. The mission highlights included studying the Saharan Air Layer, following the genesis of a tropical storm, finding a unique hybrid core or center circulation in a redeveloped storm, obtaining measurements on the strongest side of ...
05.12.2013 | Health and Medicine
05.12.2013 | Ecology, The Environment and Conservation
05.12.2013 | Information Technology
05.12.2013 | Event News
04.12.2013 | Event News
12.11.2013 | Event News