International research reveals that as cycling participation increases, a cyclist is far less likely to collide with a motor vehicle or suffer injury and death - and what's true for cyclists is true for pedestrians. And it's not simply because there are fewer cars on the roads, but because motorists seem to change their behaviour and drive more safely when they see more cyclists and pedestrians around.
Studies in many countries have shown consistently that the number of motorists colliding with walkers or cyclists doesn't increase equally with the number of people walking or bicycling. For example, a community that doubles its cycling numbers can expect a one-third drop in the per-cyclist frequency of a crash with a motor vehicle.
"It's a virtuous cycle," says Dr Julie Hatfield, an injury expert from UNSW who address a cycling safety seminar in Sydney, Australia, on September 5. "The likelihood that an individual cyclist will be struck by a motorist falls with increasing rate of bicycling in a community. And the safer cycling is perceived to be, the more people are prepared to cycle."
Experts say the effect is independent of improvements in cycling-friendly laws such as lower speed limits and better infrastructure, such as bike paths. Research has revealed the safety-in-numbers impact for cyclists in Australia, Denmark, the Netherlands, 14 European countries and 68 Californian cities.
"It's a positive effect but some people are surprised that injury rates don't go up at the same rate of increases in cycling," says Sydney University's Dr Chris Rissel, co-author of a 2008 research report on cycling.
"It appears that motorists adjust their behaviour in the presence of increasing numbers of people bicycling because they expect or experience more people cycling. Also, rising cycling rates mean motorists are more likely to be cyclists, and therefore be more conscious of, and sympathetic towards, cyclists."
Safety concerns are among the most significant barriers preventing Australians from cycling, including among those who cycle regularly, according to the report, titled Cycling: Getting Australia Moving. Despite this, over 1.68 million adults cycled in 2006, an increase of almost 250,000 since 2001. During this period, Australian capital cities experienced an average 22 percent increase in bicycle journeys to work. The city of Melbourne led with a 42 percent increase, while the city of Sydney lagged the field with a nine percent increase. 2006 figures reveal that 12,132 Sydneysiders cycle to work.
Dr Rissel says transport authorities should highlight the fun, convenience and health and environmental benefits of cycling, rather than what he views as an undue emphasis on danger and safety messages, which can deter cyclists: "We should create a cycling friendly environment and accentuate cycling's positives rather than stress negatives with 'safety campaigns' that focus on cyclists without addressing drivers and road conditions. Reminding people of injury rates and risks, to wear helmets and reflective visible clothes has the unintended effect of reinforcing fears of cycling which discourages people from cycling."
Dan Gaffney | EurekAlert!
Tool helps cities to plan electric bus routes, and calculate the benefits
09.01.2017 | International Institute for Applied Systems Analysis (IIASA)
Realistic training for extreme flight conditions
28.12.2016 | Technical University of Munich (TUM)
More and more automobile companies are focusing on body parts made of carbon fiber reinforced plastics (CFRP). However, manufacturing and repair costs must be further reduced in order to make CFRP more economical in use. Together with the Volkswagen AG and five other partners in the project HolQueSt 3D, the Laser Zentrum Hannover e.V. (LZH) has developed laser processes for the automatic trimming, drilling and repair of three-dimensional components.
Automated manufacturing processes are the basis for ultimately establishing the series production of CFRP components. In the project HolQueSt 3D, the LZH has...
Reflecting the structure of composites found in nature and the ancient world, researchers at the University of Illinois at Urbana-Champaign have synthesized thin carbon nanotube (CNT) textiles that exhibit both high electrical conductivity and a level of toughness that is about fifty times higher than copper films, currently used in electronics.
"The structural robustness of thin metal films has significant importance for the reliable operation of smart skin and flexible electronics including...
The nearby, giant radio galaxy M87 hosts a supermassive black hole (BH) and is well-known for its bright jet dominating the spectrum over ten orders of magnitude in frequency. Due to its proximity, jet prominence, and the large black hole mass, M87 is the best laboratory for investigating the formation, acceleration, and collimation of relativistic jets. A research team led by Silke Britzen from the Max Planck Institute for Radio Astronomy in Bonn, Germany, has found strong indication for turbulent processes connecting the accretion disk and the jet of that galaxy providing insights into the longstanding problem of the origin of astrophysical jets.
Supermassive black holes form some of the most enigmatic phenomena in astrophysics. Their enormous energy output is supposed to be generated by the...
The probability to find a certain number of photons inside a laser pulse usually corresponds to a classical distribution of independent events, the so-called...
Microprocessors based on atomically thin materials hold the promise of the evolution of traditional processors as well as new applications in the field of flexible electronics. Now, a TU Wien research team led by Thomas Müller has made a breakthrough in this field as part of an ongoing research project.
Two-dimensional materials, or 2D materials for short, are extremely versatile, although – or often more precisely because – they are made up of just one or a...
20.04.2017 | Event News
18.04.2017 | Event News
03.04.2017 | Event News
26.04.2017 | Materials Sciences
26.04.2017 | Agricultural and Forestry Science
26.04.2017 | Physics and Astronomy