That's important because E. coli can be spread via recycled solutions used to tenderize and enhance flavor in steaks, chops, and other cuts of meat, said U of I food science professor Susan Brewer.
The problem motivated Brewer and her graduate students to study the process used to inject meat with enhancement solutions before they're offered to consumers. And the results, published in the Journal of Food Science and Meat Science, have interested industry representatives.
"We wanted to find a point in the process at which we could exert some kind of control to keep foodborne pathogens from becoming a problem," said Brewer.
Brewer said that needle injection has been widely used for decades to tenderize meats, and more recently the fresh-meat industry has adopted the use of enhancement solutions, a practice that poultry and ham processors have used for years with very few problems.
"A certain amount of fat makes meat juicy and tasty, but in recent years consumers have been demanding leaner and leaner cuts of meat. Processors are now using the needles that tenderize steaks and chops to inject solutions that make the meat taste better and last longer," she said.
Picture a continuous end-line process in which needles inject cuts of meat with flavor boosters and shelf-life extenders. A basin catches fluid that goes through the meat or runs off the surface, and the solution is recycled into the system.
"With needle injection, organisms that exist on the outside of a piece of meat can get poked down into the meat where they're less likely to be killed if consumers like their meat on the rare side," said Brewer.
Also, as the needles inject one piece of meat after another, they can spread contamination from one piece of meat to another, and recycled enhancement solution can further complicate the spread of pathogens.
At this point, Brewer and her graduate students inserted themselves into the process to learn how contamination was likely to occur and how it could be controlled.
The scientists did two studies; in the first, they contaminated the surface of meat with E. coli K12, an indicator organism for its more dangerous relative, to observe the pathogen's progress as meat went through the system.
"We inoculated meat at various microbial loads, with some seriously nasty surface contamination on some pieces of meat," she said.
In the second study, they added E. coli K12 into the enhancement solution itself, experimenting with different components and combinations.
The scientists found that some solutions used to extend the shelf-life of meat also were effective at killing bacteria. "In certain solutions containing sodium lactate or sodium diacetate, bacteria cells couldn't grow and were substantially reduced. These shelf-life enhancers definitely work, and it really doesn't make any difference whether the steak itself or the solution is contaminated," Brewer said.
Brewer says the threat level for such meat cuts as chops, steaks, and roasts is not high, although ground meat not cooked to high temperatures can be dangerous. "You're always safe cooking red meat to 160 degrees, but if you have questions about food safety, check the USDA's Meat and Poultry Hotline at www.usda.gov," she said.
"The meat industry has been very proactive in attempting to prevent contamination of their products. They have an awful lot to lose if such an outbreak occurs," she said.
"But consumers should realize that the cook is the last point of control for eliminating these toxic organisms," she added.
"If meat is cooked until it's well done, you won't have a problem. These organisms are living cells, and they're fairly easily destroyed by heat, even E. coli 0157:H7," she said.
Researchers develop eco-friendly, 4-in-1 catalyst
25.04.2017 | Brown University
Transfecting cells gently – the LZH presents a GNOME prototype at the Labvolution 2017
25.04.2017 | Laser Zentrum Hannover e.V.
More and more automobile companies are focusing on body parts made of carbon fiber reinforced plastics (CFRP). However, manufacturing and repair costs must be further reduced in order to make CFRP more economical in use. Together with the Volkswagen AG and five other partners in the project HolQueSt 3D, the Laser Zentrum Hannover e.V. (LZH) has developed laser processes for the automatic trimming, drilling and repair of three-dimensional components.
Automated manufacturing processes are the basis for ultimately establishing the series production of CFRP components. In the project HolQueSt 3D, the LZH has...
Reflecting the structure of composites found in nature and the ancient world, researchers at the University of Illinois at Urbana-Champaign have synthesized thin carbon nanotube (CNT) textiles that exhibit both high electrical conductivity and a level of toughness that is about fifty times higher than copper films, currently used in electronics.
"The structural robustness of thin metal films has significant importance for the reliable operation of smart skin and flexible electronics including...
The nearby, giant radio galaxy M87 hosts a supermassive black hole (BH) and is well-known for its bright jet dominating the spectrum over ten orders of magnitude in frequency. Due to its proximity, jet prominence, and the large black hole mass, M87 is the best laboratory for investigating the formation, acceleration, and collimation of relativistic jets. A research team led by Silke Britzen from the Max Planck Institute for Radio Astronomy in Bonn, Germany, has found strong indication for turbulent processes connecting the accretion disk and the jet of that galaxy providing insights into the longstanding problem of the origin of astrophysical jets.
Supermassive black holes form some of the most enigmatic phenomena in astrophysics. Their enormous energy output is supposed to be generated by the...
The probability to find a certain number of photons inside a laser pulse usually corresponds to a classical distribution of independent events, the so-called...
Microprocessors based on atomically thin materials hold the promise of the evolution of traditional processors as well as new applications in the field of flexible electronics. Now, a TU Wien research team led by Thomas Müller has made a breakthrough in this field as part of an ongoing research project.
Two-dimensional materials, or 2D materials for short, are extremely versatile, although – or often more precisely because – they are made up of just one or a...
20.04.2017 | Event News
18.04.2017 | Event News
03.04.2017 | Event News
25.04.2017 | Physics and Astronomy
25.04.2017 | Materials Sciences
25.04.2017 | Life Sciences