Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Researchers discover a new genetic cause of Alzheimer’s disease

21.04.2006
Researchers from the Flanders Interuniversity Institute for Biotechnology (VIB) connected to the University of Antwerp are the first to show that the quantity of amyloid protein in brain cells is a major risk factor for Alzheimer’s disease.

Amyloid protein has already been known to be the primary component of the senile plaques in the brains of patients. The new discovery demonstrates that the greater the quantity of the protein that is produced, the younger the dementia patient is.

Alzheimer’s disease

Alzheimer’s disease is a memory disorder that affects up to 70% of all dementia patients. In Belgium, about 100,000 people suffer from this disease. The disease gradually destroys brain cells in the deep areas of the brain that are responsible for memory and knowledge. Ever since the disease was first reported by Alois Alzheimer − 100 years ago now − scientists have been searching diligently for ways to treat it.

Amyloid plaque formation plays a key role

Genetic research has previously shown a direct connection between amyloid protein and the development of senile plaques and loss of cells. Amyloid protein originates when it is cut by enzymes from a larger precursor protein. In very rare cases (fewer than 1 in 1000 patients), mutations appear in that amyloid precursor protein, causing it to change shape and be cut differently. The amyloid protein that is formed now has different characteristics, causing it to begin to stick together and precipitate as amyloid plaques. The development of amyloid plaques in the brain tissue of Alzheimer patients is a central factor in the search for a therapy for Alzheimer’s disease.

A lot or not much of the amyloid precursor protein is a risk factor The fact that patients with Down syndrome get Alzheimer’s disease shows that the quantity of the amyloid precursor protein contributes to the disease: in fact, patients with Down syndrome have 3 copies of the gene (or hereditary code) for the amyloid precursor protein and therefore produce 150% instead of 100% of the protein.

So, Jessie Theuns and her colleagues, under the direction of Christine Van Broeckhoven, hypothesized that the quantity of amyloid precursor protein might also play a role in Alzheimer’s disease. The geneticists from Antwerp systematically studied the hereditary code that is responsible for controlling the expression of the gene (= promoter). Biological processes in our body are strictly regulated, primarily by closely controlling the amount of each protein that is produced. The promoter of a gene has the most important control function in this process.

In younger Belgian and Dutch Alzheimer’s patients (younger than 70), the researchers found genetic variations in the promoter that increased the gene expression and thus the formation of the amyloid precursor protein. These variations in the promoter that increase expression occur up to 20 times more frequently (2 per 100 patients) than the mutations in the precursor protein that change the shape. Furthermore, there is a connection with the age at which the symptoms are first detected: the higher the expression (up to 150% as in Down syndrome), the younger the patient (starting between 50 and 60 years of age). Thus, the amount of amyloid precursor protein is a genetic risk factor for Alzheimer’s disease in the ageing process.

Prospects for tests and treatments

These new findings lead to a new understanding: namely, that the quantity of the amyloid precursor protein, and thus of the amyloid protein, in brain cells contributes significantly to the risk of contracting Alzheimer’s. This discovery will have to be taken into account in diagnostic tests and in the search for new medicines.

Sooike Stoops | EurekAlert!
Further information:
http://www.vib.be

More articles from Life Sciences:

nachricht Decoding the genome's cryptic language
27.02.2017 | University of California - San Diego

nachricht New risk factors for anxiety disorders
24.02.2017 | Julius-Maximilians-Universität Würzburg

All articles from Life Sciences >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: Safe glide at total engine failure with ELA-inside

On January 15, 2009, Chesley B. Sullenberger was celebrated world-wide: after the two engines had failed due to bird strike, he and his flight crew succeeded after a glide flight with an Airbus A320 in ditching on the Hudson River. All 155 people on board were saved.

On January 15, 2009, Chesley B. Sullenberger was celebrated world-wide: after the two engines had failed due to bird strike, he and his flight crew succeeded...

Im Focus: Breakthrough with a chain of gold atoms

In the field of nanoscience, an international team of physicists with participants from Konstanz has achieved a breakthrough in understanding heat transport

In the field of nanoscience, an international team of physicists with participants from Konstanz has achieved a breakthrough in understanding heat transport

Im Focus: DNA repair: a new letter in the cell alphabet

Results reveal how discoveries may be hidden in scientific “blind spots”

Cells need to repair damaged DNA in our genes to prevent the development of cancer and other diseases. Our cells therefore activate and send “repair-proteins”...

Im Focus: Dresdner scientists print tomorrow’s world

The Fraunhofer IWS Dresden and Technische Universität Dresden inaugurated their jointly operated Center for Additive Manufacturing Dresden (AMCD) with a festive ceremony on February 7, 2017. Scientists from various disciplines perform research on materials, additive manufacturing processes and innovative technologies, which build up components in a layer by layer process. This technology opens up new horizons for component design and combinations of functions. For example during fabrication, electrical conductors and sensors are already able to be additively manufactured into components. They provide information about stress conditions of a product during operation.

The 3D-printing technology, or additive manufacturing as it is often called, has long made the step out of scientific research laboratories into industrial...

Im Focus: Mimicking nature's cellular architectures via 3-D printing

Research offers new level of control over the structure of 3-D printed materials

Nature does amazing things with limited design materials. Grass, for example, can support its own weight, resist strong wind loads, and recover after being...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

Booth and panel discussion – The Lindau Nobel Laureate Meetings at the AAAS 2017 Annual Meeting

13.02.2017 | Event News

Complex Loading versus Hidden Reserves

10.02.2017 | Event News

International Conference on Crystal Growth in Freiburg

09.02.2017 | Event News

 
Latest News

New pop-up strategy inspired by cuts, not folds

27.02.2017 | Materials Sciences

Sandia uses confined nanoparticles to improve hydrogen storage materials performance

27.02.2017 | Interdisciplinary Research

Decoding the genome's cryptic language

27.02.2017 | Life Sciences

VideoLinks
B2B-VideoLinks
More VideoLinks >>>