Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Midwestern ethanol plants use much less water than western plants

16.04.2009
Iowa uses 6 gallons of water to make one gallon of ethanol - California's 2,100 gallons

Ethanol production in Minnesota and Iowa uses far less water overall than similar processes in states where water is less plentiful, a new University of Minnesota study shows.

The study, which will be published in the April 15 edition of the journal Environmental Science and Technology, is the first to compare water use in corn-ethanol production on a state-by-state basis. The authors used agricultural and geologic data from 2006-2008 to develop a ratio showing how much irrigated water was used to grow and harvest the corn and to process it at ethanol plants.

Among the major ethanol-producing states, Iowa uses the least water, with about six gallons of water used for each gallon of ethanol. Minnesota, which in 2007 produced roughly a third as much ethanol as Iowa, uses about 19 gallons of water per ethanol gallon.

States where irrigation is needed to grow corn fared far worse than those where almost no corn is irrigated. California, which produces only a tiny fraction of the nation's ethanol but irrigates most of its corn, is the largest water consumer, at about 2,100 gallons of water per gallon of ethanol. South Dakota, with total production roughly equal to Minnesota's, uses about 96 gallons of water to produce one gallon of ethanol.

Water usage could be an important factor in policy decisions about where ethanol plants are built. The study "highlights the need to strategically promote ethanol development in states with lower irrigation rates and less groundwater use," the authors say. All the states with high water usage ratios are classified by the federal government as likely to experience water shortages in coming years.

"Both energy security and water security are too important; improvement of one of them should not be made at the expense of another," said Sangwon Suh, an assistant professor in the university's department of bioproducts and biosystems engineering and the study's lead author. "Understanding the dependence of biofuel on water and its spatial disparity will be critical in implementing the biofuel policy in the United States."

The study was funded in part by the U.S. Department of Energy and by the Legislative Citizens Commission on Minnesota Resources.

Patty Mattern | EurekAlert!
Further information:
http://www.umn.edu

More articles from Ecology, The Environment and Conservation:

nachricht Bioinvasion on the rise
15.02.2017 | Universität Konstanz

nachricht Litter Levels in the Depths of the Arctic are On the Rise
10.02.2017 | Alfred-Wegener-Institut, Helmholtz-Zentrum für Polar- und Meeresforschung

All articles from Ecology, The Environment and Conservation >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: Breakthrough with a chain of gold atoms

In the field of nanoscience, an international team of physicists with participants from Konstanz has achieved a breakthrough in understanding heat transport

In the field of nanoscience, an international team of physicists with participants from Konstanz has achieved a breakthrough in understanding heat transport

Im Focus: DNA repair: a new letter in the cell alphabet

Results reveal how discoveries may be hidden in scientific “blind spots”

Cells need to repair damaged DNA in our genes to prevent the development of cancer and other diseases. Our cells therefore activate and send “repair-proteins”...

Im Focus: Dresdner scientists print tomorrow’s world

The Fraunhofer IWS Dresden and Technische Universität Dresden inaugurated their jointly operated Center for Additive Manufacturing Dresden (AMCD) with a festive ceremony on February 7, 2017. Scientists from various disciplines perform research on materials, additive manufacturing processes and innovative technologies, which build up components in a layer by layer process. This technology opens up new horizons for component design and combinations of functions. For example during fabrication, electrical conductors and sensors are already able to be additively manufactured into components. They provide information about stress conditions of a product during operation.

The 3D-printing technology, or additive manufacturing as it is often called, has long made the step out of scientific research laboratories into industrial...

Im Focus: Mimicking nature's cellular architectures via 3-D printing

Research offers new level of control over the structure of 3-D printed materials

Nature does amazing things with limited design materials. Grass, for example, can support its own weight, resist strong wind loads, and recover after being...

Im Focus: Three Magnetic States for Each Hole

Nanometer-scale magnetic perforated grids could create new possibilities for computing. Together with international colleagues, scientists from the Helmholtz Zentrum Dresden-Rossendorf (HZDR) have shown how a cobalt grid can be reliably programmed at room temperature. In addition they discovered that for every hole ("antidot") three magnetic states can be configured. The results have been published in the journal "Scientific Reports".

Physicist Dr. Rantej Bali from the HZDR, together with scientists from Singapore and Australia, designed a special grid structure in a thin layer of cobalt in...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

Booth and panel discussion – The Lindau Nobel Laureate Meetings at the AAAS 2017 Annual Meeting

13.02.2017 | Event News

Complex Loading versus Hidden Reserves

10.02.2017 | Event News

International Conference on Crystal Growth in Freiburg

09.02.2017 | Event News

 
Latest News

Stingless bees have their nests protected by soldiers

24.02.2017 | Life Sciences

New risk factors for anxiety disorders

24.02.2017 | Life Sciences

MWC 2017: 5G Capital Berlin

24.02.2017 | Trade Fair News

VideoLinks
B2B-VideoLinks
More VideoLinks >>>