Paper skin sensors for environmental monitoring

The flexible temperature array was made by drawing a resistor structure with a silver conductive ink pen on Post-it paper. © 2016 KAUST

Everyday materials found in the kitchen, such as aluminum foil, sticky note paper, sponges and tape, have been used by a team of electrical engineers from King Abdullah University of Science and Technology (KAUST) to develop a low-cost sensor that can detect external stimuli, including touch, pressure, temperature, acidity and humidity. Their work was published on February 19, 2016 in the inaugural issue of Advanced Materials Technologies by Wiley-VCH (Germany).

The sensor, which is called Paper Skin, performs as well as other artificial skin applications currently being developed while integrating multiple functions using cost-effective materials.

Wearable and flexible electronics show promise for a variety of applications, such as wireless monitoring of patient health and touch-free computer interfaces, but current research in this direction employs expensive and sophisticated materials and processes.

“Our work has the potential to revolutionize the electronics industry and opens the door to commercializing affordable high-performance sensing devices,” stated Muhammad Mustafa Hussain, KAUST associate professor of electrical engineering from the University’s Integrated Nanotechnology Lab, where the research was conducted.

“Previous efforts in this direction used sophisticated materials or processes,” Hussain continued. “Chemically functionalized inkjet printed or vacuum technology-processed papers—albeit cheap—have shown limited functionalities. Here we show a scalable ‘garage’ fabrication approach using off-the-shelf and inexpensive household elements.”

The team used sticky note paper to detect humidity, sponges and wipes to detect pressure and aluminum foil to detect motion. Coloring a sticky note with an HB pencil allowed the paper to detect acidity levels, and aluminum foil and conductive silver ink were used to detect temperature differences.

The materials were put together into a simple paper-based platform that was then connected to a device that detected changes in electrical conductivity according to external stimuli.

Increasing levels of humidity, for example, increased the platform’s ability to store an electrical charge, or its capacitance. Exposing the sensor to an acidic solution increased its resistance, while exposing it to an alkaline solution decreased it. Voltage changes were detected with temperature changes. Bringing a finger closer to the platform disturbed its electromagnetic field, decreasing its capacitance.

The team leveraged the various properties of the materials they used, including their porosity, adsorption, elasticity and dimensions to develop the low-cost sensory platform. They also demonstrated that a single integrated platform could simultaneously detect multiple stimuli in real time.

Several challenges must be overcome before a fully autonomous, flexible and multifunctional sensory platform becomes commercially achievable, explained Hussain. Wireless interaction with the paper skin needs to be developed. Reliability tests also need to be conducted to assess how long the sensor can last and how good its performance is under severe bending conditions.

“The next stage will be to optimize the sensor’s integration on this platform for applications in medical monitoring systems. The flexible and conformal sensory platform will enable simultaneous real-time monitoring of body vital signs, such as heart rate, blood pressure, breathing patterns and movement,” Hussain said.

“We may also transfer the achieved functionalities of the technology to biologically grown skin and develop mechanisms to connect it to neuronal networks in the human body to assist burn victims, for example. Other applications include robotics, vehicular technology and environmental surveys,” he added.

KAUST-NSF Research Conference on Electronic Materials, Devices and Systems for a Sustainable Future:

From March 14 to 16, 2016 Hussain and colleagues from KAUST and the United States National Science Foundation (NSF) will host the KAUST-NSF Research Conference on Electronic Materials, Devices and Systems for a Sustainable Future on the KAUST campus. Work in the electronics field, such as Hussain's low-cost paper sensor, will be highlighted during the three-day event.

The conference will also provide the opportunity for the KAUST scholarly community to exhibit research and innovations through a poster presentation session. Submission for posters will be available from February 21 to March 1.

The conference is made possible with financial support from the KAUST Office of Sponsored Research. It is co-sponsored by the National Science Foundation (NSF), United States of America, KAUST Industry Collaboration Program (KICP) and the Computer, Electrical and Mathematical Science and Engineering (CEMSE) Division.

https://discovery.kaust.edu.sa/en/article/196/artificial-skin-sensors-made-from-sticky-notes
DOI: 10.1002/admt.201600004

About Muhammad Mustafa Hussain:
Muhammad Mustafa Hussain (Ph.D., The University of Texas at Austin, U.S., December 2005) is associate professor of electrical engineering at KAUST. Before joining the University, he was a program manager of the emerging technology program in SEMATECH (Austin, Texas, U.S.), funded by DARPA NEMS, CERA and STEEP programs.

A regular panelist of U.S. NSF grant reviewing committees, Hussain is also editor-in-chief of Applied Nanoscience (Springer), editor of IEEE Transactions on Electron Devices and an IEEE senior member. He has served as a first or corresponding author in 80% of his 232 research papers and has 41 issued or pending U.S. patents.

About King Abdullah University of Science and Technology:
King Abdullah University of Science and Technology (KAUST) is an international, graduate-level research university located along the Red Sea in Saudi Arabia. KAUST is dedicated to advancing science and technology through interdisciplinary research, education and innovation. Curiosity driven and goal-oriented research is conducted by students, faculty, scientists and engineers to address the world’s pressing scientific and technological challenges related to food, water, energy and the environment. www.kaust.edu.sa

Associated links
Original article from King Abdullah University of Science and Technology

Journal information

Advanced Materials Technologies

Media Contact

Michelle D'Antoni Research SEA

More Information:

http://www.researchsea.com

All latest news from the category: Materials Sciences

Materials management deals with the research, development, manufacturing and processing of raw and industrial materials. Key aspects here are biological and medical issues, which play an increasingly important role in this field.

innovations-report offers in-depth articles related to the development and application of materials and the structure and properties of new materials.

Back to home

Comments (0)

Write a comment

Newest articles

Results for control of pollutants in water

Brazilian scientists tested a simple and sustainable method for monitoring and degrading a mixture of polycyclic aromatic hydrocarbons, compounds present in fossil fuels and industrial waste. An article published in the journal Catalysis…

A tandem approach for better solar cells

Perovskite-based solar cells were first proved in 2009 to have excellent light-absorbing properties of methylammonium lead bromide and methylammonium lead iodide, collectively referred to as lead halide perovskites or, more…

The behavior of ant queens is shaped by their social environment

Specialization of ant queens as mere egg-layers is reversible / Queen behavioral specialization is initiated and maintained by the presence of workers. The queens in colonies of social insects, such…

Partners & Sponsors