Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Lead levels in drinking water spike when copper and lead pipes joined

19.12.2011
Levels linked to galvanic corrosion, disinfectants, pH

Lead pipes once used routinely in municipal water distribution systems are a well-recognized source of dangerous lead contamination, but new research from Washington University in St. Louis suggests that the partial replacement of these pipes can make the problem worse.

The research shows that joining old lead pipes with new copper lines using brass fittings spurs galvanic corrosion that can dramatically increase the amount of lead released into drinking water supplies.

“Work done in our laboratory shows galvanic corrosion in joined service lines is significant and lasts for a long time,” says Dan Giammar, PhD, the Harold D. Jolley Career Development Associate Professor in the Department of Energy, Environmental & Chemical Engineering at Washington University in St. Louis.

His study, published in the Proceedings of the 2011 Water Quality Technology Conference, suggests that safety-minded, lead-pipe-removal programs at water utilities across the country actually may be increasing the risk of lead exposure for water customers.

An experiment running in his aquatic chemistry lab shows why. It features 80- to 100-year-old lead water pipes that were dug out of the ground in Washington, D.C., and shipped to his St. Louis laboratory. Some of the lead pipes have been cut and then joined with brass couplings to brand new copper pipe.

This setup mimics what happens if a utility company is replacing lead service lines and homeowners decline to have their sections of the lines replaced.

A service line runs from the main to the home. The utility owns the part from the main to the homeowner's property line and the homeowner owns the part from the property line to the house. The utility cannot replace the homeowner’s half of the line unless the homeowner gives permission and pays for replacement. In the U.S. only 10 percent of homeowners agree to the charge.

“Since you started with a whole lead pipe and you now have half a lead pipe, you might think your problem would be half of what it was or — maybe — completely unchanged,” Giammar says.

His experiment reveals that instead, it could be far worse. The joined lead-copper pipe in his lab releases five times more lead than did the original lead pipe.

The lead is released by galvanic corrosion, a process set up whenever two dissimilar metals are immersed in a conducting liquid.

The same thing happens if lasagna or another acidic dish is made in a stainless steel pan, covered with aluminum foil, and placed in a refrigerator. The two metals and the lasagna act as a galvanic cell, and some of the aluminum may migrate out of the foil and plate out on the surface of the lasagna.

The Lead and Copper Rule
The project to measure galvanic corrosion of lead pipes was the third Giammar has done for the Water Research Foundation, an organization of water utilities that allows them to pool their money to support research on problems of common interest.

Giammar, who calls himself a heavy metals guy, did his doctoral work on uranium contamination of soil and groundwater, work relevant to the far-flung branches of the Manhattan Project that purified uranium for the atomic bomb during World War II.

He still works on uranium remediation, but when he moved to St. Louis in 2002, he thought that he really ought to work on lead as well, because Missouri has historically been one of the two largest lead-producing states in the country. The other is Alaska.

Giammar began with experiments directed at understanding exactly what happens when phosphates are worked into lead contaminated soil. Under the right conditions, the phosphate will bind to the lead and immobilize it.

Phosphate remediation of lead contaminated soils had been successful in Joplin, Mo., a town located in the Tri-State district, an historic lead-zinc mining district that takes in parts of Missouri, Kansas and Oklahoma.

While Giammar was working with phosphates and soils, the media began reporting that lead levels in the tap water in Washington, D.C., were higher than before and indeed were higher than national drinking water standards allowed.

Lead, as Giammar says, is a “xenobiotic” element (literally foreign to living systems). Unlike some metals, it serves no biological purpose and only does harm. But lead pipes weren’t outlawed in new construction until 1978.

That the district knew it had a problem was remarkable in itself. The levels of lead in drinking water weren’t regulated until 1991, when the Lead and Copper Rule was passed.

The lead levels in Washington, D.C., drinking water began to rise in 2001.

The case of Washington, D.C., water

The lead levels rose for an interesting reason, says Giammar. The district water utility was trying to improve water quality.

In the U.S., he explains, water is delivered with a disinfectant still in it. There are two ways of chlorinating water to disinfect it. Utilities either use free chlorine, which is essentially bleach, or they use chloramines, which are essentially bleach combined with ammonia.

Free chlorine is a better disinfectant but it also forms higher concentrations of chlorinated disinfection byproducts — things like chloroform — that we don’t want in our drinking water, Giammar says.

In an effort to decrease the concentrations of disinfection byproducts, the district switched from chlorine to chloramine.

This is where the water chemistry comes in. “The lead pipe, in itself, is not much of a concern,” Giammar says. Pure lead, lead 0 as it’s called, is not particularly reactive or soluble, which is one of the reasons people made plumbing out of it. Lead pipes last much longer than iron pipes.

But lead can oxidize — essentially corrode. The lead species that then form determine how much lead ends up in the water. The various forms of lead in the +2 oxidation state are all more soluble than lead 0, but lead sulfate is more soluble than lead carbonate, which is in turn more soluble than lead phosphate. (The oxidation state of an element is a rough measure of how many electrons it has "lost to other, nearby elements that are attracting the electrons more strongly.)

When it comes to lead in the +4 oxidation state there’s a twist.

“If you have a strong oxidant, you can form species with lead in the +4 oxidation state,” Giammar says. “These have very low solubility but they’re only stable in the presence of a strong oxidant. As soon as the strong oxidant goes away, the lead +4 is no longer stable. It starts to come back to lead +2, and it can release the lead quite quickly.”

The free chlorine the district had been using is a very strong oxidant. The chloramines they switched to are less strong.

“So when they switched to chloramines, the pipe scale that had formed over years of chlorine treatment began to release lead into the water,” Giammar says. It was a classic example of an unintended consequence.

What the district case demonstrates, Giammar says, is that tap water is a manufactured product, not a natural resource. The water leaving the treatment plant can have essentially no lead in it, but by the time it reaches the faucet that could have changed.

The lead comes from the piping, but whether it is released depends on the chemistry of the water running through the distribution system.

Looking at water chemistry
When he read about the district problem, Giammar wrote a proposal to the Water Research Board offering to study the chemistry of the insides of pipes, particularly the dissolution rates of lead phosphates, lead carbonates and the lead +4 oxides, as a function of pH, added phosphate and disinfectants.

“That was our first entry into the field of lead and drinking water,” he says.

“We knew pH would be an important variable,” he says. “You don’t want your pH to fall too low, especially for the lead carbonates, which dissolve at lower pH.”

“But we didn’t realize how important pH was. We studied water samples with a pH of 10, 8.5 and 7.5. You wouldn’t think there would be a much of a difference between a pH of 8.5 and 7.5, but there was.

“In some cases, the pH made the difference between a lead concentration that met the drinking water standard and one that didn’t.”

Phosphate also turned out to be important. “It had a huge impact on the dissolution rates of all the lead corrosion products we studied,” says Giammar.

So one way to bring down lead levels is to add phosphate. But phosphate costs money, so the utilities want to add as little of it as they can to produce a good-quality water.

“It’s never going to be a one-size-fits all solution because the source-water compositions are different,” says Giammar, “but we came up with some pretty strong recommendations.”

The final report on the project, “Influence of Water Chemistry on the Dissolution and Transformation Rates of Lead Corrosion Products,” was published last year.

Should you let the tap run?
“Another thing we studied in that first project,” Giammar says, “was whether we should be more worried about reaction rates or about the equilibrium state of the reactions.

“To put it another way, if you let the water sit in the pipes for six hours, will it be different from water that sat in the pipes for only an hour?”

It turned out that most lead species dissolve relatively quickly, so reaction rates are not particularly important. The water is the same no matter how long the water has been sitting in the pipes.

But this isn’t true of the lead +4 oxides, the material that formed the scale inside the Washington, D.C., pipes. “They are never at equilibrium with the water flowing over them,” Giammar says. “Instead everything depends on the rate at which those oxides form or the rate at which they dissolve.”

So Giammar proposed a second project for the Water Research Foundation just to study the lead +4 oxides. “They’re fascinating solids,” he says.

Then Giammar’s lab picked up a third project. “A little over a year ago, I got a call from an environmental engineer in Washington, D.C., who was looking at something called galvanic corrosion and its potential to release lead into drinking water,“ he says.

This is the project that led to the centenarian lead pipe experiment now taking up much of the bench space in his lab.

Unlike some of the other water problems he has studied, galvanic corrosion is national in scope. The Environmental Protection Agency is concerned enough that it has appointed a science advisory board to make recommendations on how best to deal with it, Giammar says.

How low can we go?
It’s difficult to talk about lead in a sensible way. The current threshold for drinking water is 15 micrograms per liter, Giammar says. And while there’s talk in the community about lowering the allowable levels of some water contaminants, lead is not among them.

Environmental lead is ubiquitous and everyone has measurable levels of lead in their blood. We are exposed to it through dust and air as well as through water, thanks in part to the tetraethyl lead added to gasoline as an antiknock compound for 80 years.

“If your dominant exposure is through dust, there’s little benefit to ratcheting down your exposure to water even further,” Giammar says.

But, he says, because of the Lead and Copper Rule, water utilities now monitor lead levels. And he learned at a recent conference that during the most recent monitoring period, only 30 utilities had lead levels above the drinking water standard.

That may seem like a lot, he said, but there are roughly 54,000 water utilities in the U.S.

Diana Lutz | EurekAlert!
Further information:
http://www.wustl.edu

More articles from Studies and Analyses:

nachricht New study: How does Europe become a leading player for software and IT services?
03.04.2017 | Fraunhofer-Institut für System- und Innovationsforschung (ISI)

nachricht Reusable carbon nanotubes could be the water filter of the future, says RIT study
30.03.2017 | Rochester Institute of Technology

All articles from Studies and Analyses >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: Making lightweight construction suitable for series production

More and more automobile companies are focusing on body parts made of carbon fiber reinforced plastics (CFRP). However, manufacturing and repair costs must be further reduced in order to make CFRP more economical in use. Together with the Volkswagen AG and five other partners in the project HolQueSt 3D, the Laser Zentrum Hannover e.V. (LZH) has developed laser processes for the automatic trimming, drilling and repair of three-dimensional components.

Automated manufacturing processes are the basis for ultimately establishing the series production of CFRP components. In the project HolQueSt 3D, the LZH has...

Im Focus: Wonder material? Novel nanotube structure strengthens thin films for flexible electronics

Reflecting the structure of composites found in nature and the ancient world, researchers at the University of Illinois at Urbana-Champaign have synthesized thin carbon nanotube (CNT) textiles that exhibit both high electrical conductivity and a level of toughness that is about fifty times higher than copper films, currently used in electronics.

"The structural robustness of thin metal films has significant importance for the reliable operation of smart skin and flexible electronics including...

Im Focus: Deep inside Galaxy M87

The nearby, giant radio galaxy M87 hosts a supermassive black hole (BH) and is well-known for its bright jet dominating the spectrum over ten orders of magnitude in frequency. Due to its proximity, jet prominence, and the large black hole mass, M87 is the best laboratory for investigating the formation, acceleration, and collimation of relativistic jets. A research team led by Silke Britzen from the Max Planck Institute for Radio Astronomy in Bonn, Germany, has found strong indication for turbulent processes connecting the accretion disk and the jet of that galaxy providing insights into the longstanding problem of the origin of astrophysical jets.

Supermassive black holes form some of the most enigmatic phenomena in astrophysics. Their enormous energy output is supposed to be generated by the...

Im Focus: A Quantum Low Pass for Photons

Physicists in Garching observe novel quantum effect that limits the number of emitted photons.

The probability to find a certain number of photons inside a laser pulse usually corresponds to a classical distribution of independent events, the so-called...

Im Focus: Microprocessors based on a layer of just three atoms

Microprocessors based on atomically thin materials hold the promise of the evolution of traditional processors as well as new applications in the field of flexible electronics. Now, a TU Wien research team led by Thomas Müller has made a breakthrough in this field as part of an ongoing research project.

Two-dimensional materials, or 2D materials for short, are extremely versatile, although – or often more precisely because – they are made up of just one or a...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

Expert meeting “Health Business Connect” will connect international medical technology companies

20.04.2017 | Event News

Wenn der Computer das Gehirn austrickst

18.04.2017 | Event News

7th International Conference on Crystalline Silicon Photovoltaics in Freiburg on April 3-5, 2017

03.04.2017 | Event News

 
Latest News

NASA's Fermi catches gamma-ray flashes from tropical storms

25.04.2017 | Physics and Astronomy

Researchers invent process to make sustainable rubber, plastics

25.04.2017 | Materials Sciences

Transfecting cells gently – the LZH presents a GNOME prototype at the Labvolution 2017

25.04.2017 | Life Sciences

VideoLinks
B2B-VideoLinks
More VideoLinks >>>