Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Brass Devices in Plumbing Systems Can Create Serious Lead-In-Water Problems

12.11.2010
A new research study highlights problems with some brass products in plumbing systems that can leach very high levels of lead into drinking water, even in brand new buildings – and suggests that such problems may often go undetected.

Lead is a heavy metal that can harm the nervous system and brain development, and is especially dangerous for pregnant women, infants and children.

The study, published in the November issue of the Journal of the American Water Works Association, is the result of collaborative research between the University of North Carolina at Chapel Hill and Virginia Tech.

The research was conducted by Carolyn Elfland, associate vice chancellor for campus services at UNC, along with Marc Edwards, Ph.D., the Charles Lunsford Professor of Civil Engineering, and Paolo Scardina, Ph.D., assistant professor of practice, both at the Virginia Tech Charles E. Via Department of Civil and Environmental Engineering.

The collaboration started in early 2007, when UNC discovered high lead levels in water in new buildings and asked Virginia Tech to assist in diagnosing and remedying the problem. The team developed a flushing protocol, which aims to ensure that before buildings are occupied, new faucets and water fountains met the Environmental Protection Agency’s Lead and Copper Rule of less than 15 micrograms of lead per liter of water, or 15 parts per billion. The researchers also determined that switching to plumbing devices that meet specifications required under California law, which is stricter than federal regulations, would not solve the problem.

Then, in mid-2008, an unusually severe problem arose with two drinking fountains in a large new laboratory building; in particular, one fountain had lead levels exceeding 300 parts per billion. Repeated attempts to flush the lead over several months and to use conventional remedial measures were unsuccessful. The problem was eventually traced to a source in the building’s piping system upstream of the water fountains. The cause was a particular type of ball valve and the problem disappeared when the valves were finally removed. The valves were later found to have as much as 18 percent lead by weight on the inner surfaces contacting the drinking water; later laboratory testing proved they would leach lead at levels high above the EPA standard for months.

The valves were considered legal, because their average overall lead content was just under the 8 percent limit allowed by law, and were listed as having passed the lead leaching standards of NSF International, the plumbing device industry’s national standard-setting body. While there have been other verified cases of brass devices like faucets and water fountains at the end of plumbing lines leaching high lead to water, this situation is the first time that a device upstream in a plumbing line has been proven to leach dangerous levels of lead to drinking water that reached the tap. It verified earlier research by Edwards (http://www.nsf.gov/news/news_summ.jsp?cntn_id=104334), which expressed concern about relatively lax standards testing used to certify brass devices for use in plumbing systems as safe. In response to that work, NSF International implemented more rigorous criteria, due to come into effect in 2012. However, these tougher standards reflect the California standards, and the UNC-Virginia Tech research team’s experience indicates that they probably are still too lax, the authors said.

Edwards, named a MacArthur Fellow in 2007, said the case highlighted concerns about high lead content in certain brass plumbing devices, and the need for a method of preventing the installation of defective products in new construction.

“The levels of lead detected at UNC exceeded those known to cause elevated blood lead in children, as established by the Centers for Disease Control, and even levels causing acute lead toxicity established by the Consumer Product Safety Commission,” he said. “Thankfully, UNC’s procedures caught the problem before anyone could be exposed to the high lead in water, but in most other cases the issue would go undetected. The fact that some defective products, listed as safe, could be installed in schools and day care centers and harm children is very troubling”

Elfland noted that high lead in water was first identified as a problem during the days of the Roman Empire and that lead solder and lead pipes have been outlawed for decades.

“People have a right to expect that drinking water in brand new buildings will not be contaminated by lead, and building owners should not have to go the effort and expense UNC does to ensure that expectation is met,” she said “In my opinion, this is a major regulatory failure.”

The UNC-Virginia Tech team’s research demonstrated that the higher cost of devices that are truly “lead free” would end up saving money. UNC’s standard pre-occupancy flushing protocol adds $49 to $91 (or between 24 percent to 45 percent) to the cost of every fixture. Elfland also noted that the total cost of finding and replacing the problematic valves in the plumbing system was $30,000, if the salaries of all the people who worked on the problem were included. The valves originally cost less than $20 each.

Earlier this fall, a U.S. Senate bill to lower the allowable amount of lead in brass plumbing devices from 8 percent to a weighted average of 0.25 percent was introduced by Sen. Barbara Boxer (D-Calif.), chairwoman of the Senate Environment and Public Works Committee. “The bottom line is that there is no safe level of lead – a toxic heavy metal – in our drinking water,” Boxer said in a news release at the bill’s introduction.

Journal website: http://www.awwa.org/publications/JournalCurrent.cfm

UNC News Services contact: Patric Lane, (919) 962-8596, patric_lane@unc.edu
Virginia Tech College of Engineering contact: Steven Mackay, (540) 231-4787, smackay@vt.edu

Patric Lane | Newswise Science News
Further information:
http://www.unc.edu

Further reports about: Lead-In-Water NSF UNC drinking water environmental risk plumbing system

More articles from Studies and Analyses:

nachricht New study: How does Europe become a leading player for software and IT services?
03.04.2017 | Fraunhofer-Institut für System- und Innovationsforschung (ISI)

nachricht Reusable carbon nanotubes could be the water filter of the future, says RIT study
30.03.2017 | Rochester Institute of Technology

All articles from Studies and Analyses >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: Making lightweight construction suitable for series production

More and more automobile companies are focusing on body parts made of carbon fiber reinforced plastics (CFRP). However, manufacturing and repair costs must be further reduced in order to make CFRP more economical in use. Together with the Volkswagen AG and five other partners in the project HolQueSt 3D, the Laser Zentrum Hannover e.V. (LZH) has developed laser processes for the automatic trimming, drilling and repair of three-dimensional components.

Automated manufacturing processes are the basis for ultimately establishing the series production of CFRP components. In the project HolQueSt 3D, the LZH has...

Im Focus: Wonder material? Novel nanotube structure strengthens thin films for flexible electronics

Reflecting the structure of composites found in nature and the ancient world, researchers at the University of Illinois at Urbana-Champaign have synthesized thin carbon nanotube (CNT) textiles that exhibit both high electrical conductivity and a level of toughness that is about fifty times higher than copper films, currently used in electronics.

"The structural robustness of thin metal films has significant importance for the reliable operation of smart skin and flexible electronics including...

Im Focus: Deep inside Galaxy M87

The nearby, giant radio galaxy M87 hosts a supermassive black hole (BH) and is well-known for its bright jet dominating the spectrum over ten orders of magnitude in frequency. Due to its proximity, jet prominence, and the large black hole mass, M87 is the best laboratory for investigating the formation, acceleration, and collimation of relativistic jets. A research team led by Silke Britzen from the Max Planck Institute for Radio Astronomy in Bonn, Germany, has found strong indication for turbulent processes connecting the accretion disk and the jet of that galaxy providing insights into the longstanding problem of the origin of astrophysical jets.

Supermassive black holes form some of the most enigmatic phenomena in astrophysics. Their enormous energy output is supposed to be generated by the...

Im Focus: A Quantum Low Pass for Photons

Physicists in Garching observe novel quantum effect that limits the number of emitted photons.

The probability to find a certain number of photons inside a laser pulse usually corresponds to a classical distribution of independent events, the so-called...

Im Focus: Microprocessors based on a layer of just three atoms

Microprocessors based on atomically thin materials hold the promise of the evolution of traditional processors as well as new applications in the field of flexible electronics. Now, a TU Wien research team led by Thomas Müller has made a breakthrough in this field as part of an ongoing research project.

Two-dimensional materials, or 2D materials for short, are extremely versatile, although – or often more precisely because – they are made up of just one or a...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

Expert meeting “Health Business Connect” will connect international medical technology companies

20.04.2017 | Event News

Wenn der Computer das Gehirn austrickst

18.04.2017 | Event News

7th International Conference on Crystalline Silicon Photovoltaics in Freiburg on April 3-5, 2017

03.04.2017 | Event News

 
Latest News

From volcano's slope, NASA instrument looks sky high and to the future

27.04.2017 | Earth Sciences

Control of molecular motion by metal-plated 3-D printed plastic pieces

27.04.2017 | Materials Sciences

Move over, Superman! NIST method sees through concrete to detect early-stage corrosion

27.04.2017 | Materials Sciences

VideoLinks
B2B-VideoLinks
More VideoLinks >>>