Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Researcher proves mass is important at the nano-scale, matters in calculations and measurements

22.01.2014
A UT Arlington engineering professor has proven that the effect of mass is important, can be measured and has a significant impact on any calculations and measurements at the sub-micrometer scale.

The findings help to better understand movement of nano-sized objects in fluid environments that can be characterized by a low Reynolds number, which often occurs in biological systems. The unconventional results are consistent with Newton’s Second Law of Motion, a well-established law of physics, and imply that mass should be included in the dynamic model of these nano-systems. The most widely accepted models omit mass at that scale.

Alan Bowling, an assistant professor of mechanical and aerospace engineering, collaborated with Samarendra Mohanty, an assistant physics professor, and doctoral students Mahdi Haghshenas-Jaryani, Bryan Black and Sarvenaz Ghaffari, as well as graduate student James Drake to make the discovery.

A key advantage of the new model is that it can be used to build computer simulations of nano-sized objects that have drastically reduced run times as compared to a conventional model based on Newton’s second law. These conventional models have run times of days, weeks, months and years while the new model requires only seconds or minutes to run.

In the past, researchers attempted to address the long run time by omitting the mass terms in the model. This resulted in faster run times but, paradoxically, violated Newton’s second law upon which the conventional model was based. The remedy for this paradox was to argue that mass was unimportant at the nano-scale.

However, the new model retains mass, and predicts unexpected motion of nano-sized objects in a fluid that has been experimentally observed. The new model also runs much faster than both the conventional and massless models.

It is expected that this new model will significantly accelerate research involving small-scale phenomena.

Research areas that Bowling and collaborators at UT Arlington are currently investigating include cell migration, protein function, bionic medical devices and nanoparticle suspensions for storing thermal energy. However, the applications for the computer simulation in medicine, biology, and other fields are endless.

The research is detailed in the paper “Dynamics of Microscopic Objects in Optical Tweezers: Experimental Determination of Underdamped Regime and Numerical Simulation using Multiscale Analysis” and published online by the Journal of Non-Linear Dynamics. The paper is scheduled for publication in the journal’s print version later this year.

Khosrow Behbehani, dean of the College of Engineering, said the team’s findings may alter ways of thinking throughout the engineering and scientific worlds.

“The paper is only the beginning for this research,” Behbehani said. “I anticipate a high level of interest in the findings. It could transform the way we conduct research in nano-engineering by providing researchers with the ability to study such physical phenomena at such small scale through the model.”

The team used optical tweezers previously developed by Mohanty to measure oscillations that occur at the nano scale, thus proving that mass and acceleration must be considered at that level as well.

“We proved it in the lab,” Bowling said. “Publication in an accepted journal is the next step in gaining mass acceptance of the idea, which flies in the face of what most people believe now.”

The discovery resulted from a 2012 National Science Foundation grant project in which the UT Arlington team investigated a new model for how motor proteins behave in the body. The NSF award was funded through the Early Concept Grants for Exploratory Research, or EAGER program. The grants support exploratory work in its early stages on untested, but potentially transformative, research ideas or approaches.

The University of Texas at Arlington is a comprehensive research institution of more than 33,300 students and 2,300 faculty members in the epicenter of North Texas. It is the second largest institution in the University of Texas System. Research expenditures reached almost $78 million last year. Visit www.uta.edu for more information.

Herb Booth | EurekAlert!
Further information:
http://www.uta.edu

More articles from Physics and Astronomy:

nachricht Nanotechnology for energy materials: Electrodes like leaf veins
27.09.2016 | Helmholtz-Zentrum Berlin für Materialien und Energie GmbH

nachricht First quantum photonic circuit with electrically driven light source
27.09.2016 | Westfälische Wilhelms-Universität Münster

All articles from Physics and Astronomy >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: First quantum photonic circuit with electrically driven light source

Optical quantum computers can revolutionize computer technology. A team of researchers led by scientists from Münster University and KIT now succeeded in putting a quantum optical experimental set-up onto a chip. In doing so, they have met one of the requirements for making it possible to use photonic circuits for optical quantum computers.

Optical quantum computers are what people are pinning their hopes on for tomorrow’s computer technology – whether for tap-proof data encryption, ultrafast...

Im Focus: OLED microdisplays in data glasses for improved human-machine interaction

The Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP has been developing various applications for OLED microdisplays based on organic semiconductors. By integrating the capabilities of an image sensor directly into the microdisplay, eye movements can be recorded by the smart glasses and utilized for guidance and control functions, as one example. The new design will be debuted at Augmented World Expo Europe (AWE) in Berlin at Booth B25, October 18th – 19th.

“Augmented-reality” and “wearables” have become terms we encounter almost daily. Both can make daily life a little simpler and provide valuable assistance for...

Im Focus: Artificial Intelligence Helps in the Discovery of New Materials

With the help of artificial intelligence, chemists from the University of Basel in Switzerland have computed the characteristics of about two million crystals made up of four chemical elements. The researchers were able to identify 90 previously unknown thermodynamically stable crystals that can be regarded as new materials. They report on their findings in the scientific journal Physical Review Letters.

Elpasolite is a glassy, transparent, shiny and soft mineral with a cubic crystal structure. First discovered in El Paso County (Colorado, USA), it can also be...

Im Focus: Complex hardmetal tools out of the 3D printer

For the first time, Fraunhofer IKTS shows additively manufactured hardmetal tools at WorldPM 2016 in Hamburg. Mechanical, chemical as well as a high heat resistance and extreme hardness are required from tools that are used in mechanical and automotive engineering or in plastics and building materials industry. Researchers at the Fraunhofer Institute for Ceramic Technologies and Systems IKTS in Dresden managed the production of complex hardmetal tools via 3D printing in a quality that are in no way inferior to conventionally produced high-performance tools.

Fraunhofer IKTS counts decades of proven expertise in the development of hardmetals. To date, reliable cutting, drilling, pressing and stamping tools made of...

Im Focus: Launch of New Industry Working Group for Process Control in Laser Material Processing

At AKL’16, the International Laser Technology Congress held in May this year, interest in the topic of process control was greater than expected. Appropriately, the event was also used to launch the Industry Working Group for Process Control in Laser Material Processing. The group provides a forum for representatives from industry and research to initiate pre-competitive projects and discuss issues such as standards, potential cost savings and feasibility.

In the age of industry 4.0, laser technology is firmly established within manufacturing. A wide variety of laser techniques – from USP ablation and additive...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

Laser use for neurosurgery and biofabrication - LaserForum 2016 focuses on medical technology

27.09.2016 | Event News

Experts from industry and academia discuss the future mobile telecommunications standard 5G

23.09.2016 | Event News

ICPE in Graz for the seventh time

20.09.2016 | Event News

 
Latest News

New switch decides between genome repair and death of cells

27.09.2016 | Life Sciences

Nanotechnology for energy materials: Electrodes like leaf veins

27.09.2016 | Physics and Astronomy

‘Missing link’ found in the development of bioelectronic medicines

27.09.2016 | Life Sciences

VideoLinks
B2B-VideoLinks
More VideoLinks >>>