Investigators from the Centers for Disease Control and Prevention (CDC) describe pathologic findings from 40 case reports of fungal infection in patients who had been given contaminated epidural, paraspinal, or intra-articular (into joints) steroid injections and correlate these findings with clinical and laboratory data. The report, published in the September issue of The American Journal of Pathology, alerts clinicians and the general public to the catastrophic dangers of contaminated epidural injections.
This shows fungal hyphae (red) in brain of a fatal case as seen using polyfungal immunohistochemistry.
Credit: The American Journal of Pathology/Ritter et al.
In September 2012, CDC began hearing multiple reports of fungal meningitis in patients following epidural steroid injections. By June 2013, 745 people had confirmed infections and 58 had died, making this the largest reported outbreak of infections associated with epidural and intra-articular injections.
After intensive investigation, the contamination was traced to more than 17,000 vials from three contaminated lots of preservative-free methylprednisolone acetate (MPA) originating from a single compounding pharmacy. More than 13,000 people were injected with the potentially contaminated drug. Most cases were attributable to Exserohilum rostratum, a dark-colored environmental mold that rarely infects humans.
Researchers, including the CDC's Exserohilum Infections Working Group, report that of 40 cases reviewed, 16 were fatal, and all except two fatal cases had a clinical diagnosis of meningitis. Autopsy examination showed extensive hemorrhage and necrosis (tissue decay) around the base of the brain and thrombi (clots) involving the basilar arterial circulation.
Tissue specimens from infected individuals showed inflammation of the leptomeninges (thin membranes lining the brain) and blood vessel walls within the brain. Distinctive abnormalities were observed around blood vessels, and fungus was found around and within arterial walls. Interestingly, fungus deep within the brain tissue itself was found in only one case.
Similar pathologic findings were seen at the epidural injection site. Fungus was not found in tissue samples taken from the heart, lung, liver, or kidney.
Investigators wondered why fungus injected in the spinal region should target the base of the brain. "The observation of abundant fungi in the perivascular tissues, but relatively low numbers of fungi inside blood vessels, suggests migration of fungus into, rather than out of, vessels at this location. This supports the hypothesis that Exserohilum migrates from the lumbar spine to the brain through the cerebrospinal fluid with subsequent vascular invasion, rather than migration through the vasculature," suggests Jana M. Ritter, DVM, a veterinary pathologist at the CDC's Infectious Diseases Pathology Branch.
In addition to characterizing the histopathology seen in this outbreak, the authors also provide practical information for pathologists, including an evaluation of various diagnostic methods to detect the fungal infection in tissues. Polyfungal immunohistochemistry (IHC) in formalin-fixed paraffin-embedded tissues (FFPE) was found to be the most sensitive method. IHC identified fungus in 100% of cases, compared with 43% by standard hematoxylin-eosin (H&E) and 95% with Grocott's methenamine silver (GMS) stains. Factors that may affect cellular inflammatory patterns and fungal concentration are discussed, and the authors note that their findings may reflect the simultaneous introduction of the fungus along with the steroid.
Contributors to the investigation also included researchers from the Office of the Chief Medical Examiner, Louisville, KY and the Department of Pathology, University of Michigan, Ann Arbor, MI.
Eileen Leahy | EurekAlert!
Custom-tailored strategy against glioblastomas
26.09.2016 | Rheinische Friedrich-Wilhelms-Universität Bonn
New leukemia treatment offers hope
23.09.2016 | King Abdullah University of Science and Technology
Friction stir welding is a still-young and thus often unfamiliar pressure welding process for joining flat components and semi-finished components made of light metals.
Scientists at the University of Stuttgart have now developed two new process variants that will considerably expand the areas of application for friction stir welding.
Technologie-Lizenz-Büro (TLB) GmbH supports the University of Stuttgart in patenting and marketing its innovations.
Friction stir welding is a still-young and thus often unfamiliar pressure welding process for joining flat components and semi-finished components made of...
Optical quantum computers can revolutionize computer technology. A team of researchers led by scientists from Münster University and KIT now succeeded in putting a quantum optical experimental set-up onto a chip. In doing so, they have met one of the requirements for making it possible to use photonic circuits for optical quantum computers.
Optical quantum computers are what people are pinning their hopes on for tomorrow’s computer technology – whether for tap-proof data encryption, ultrafast...
The Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP has been developing various applications for OLED microdisplays based on organic semiconductors. By integrating the capabilities of an image sensor directly into the microdisplay, eye movements can be recorded by the smart glasses and utilized for guidance and control functions, as one example. The new design will be debuted at Augmented World Expo Europe (AWE) in Berlin at Booth B25, October 18th – 19th.
“Augmented-reality” and “wearables” have become terms we encounter almost daily. Both can make daily life a little simpler and provide valuable assistance for...
With the help of artificial intelligence, chemists from the University of Basel in Switzerland have computed the characteristics of about two million crystals made up of four chemical elements. The researchers were able to identify 90 previously unknown thermodynamically stable crystals that can be regarded as new materials. They report on their findings in the scientific journal Physical Review Letters.
Elpasolite is a glassy, transparent, shiny and soft mineral with a cubic crystal structure. First discovered in El Paso County (Colorado, USA), it can also be...
For the first time, Fraunhofer IKTS shows additively manufactured hardmetal tools at WorldPM 2016 in Hamburg. Mechanical, chemical as well as a high heat resistance and extreme hardness are required from tools that are used in mechanical and automotive engineering or in plastics and building materials industry. Researchers at the Fraunhofer Institute for Ceramic Technologies and Systems IKTS in Dresden managed the production of complex hardmetal tools via 3D printing in a quality that are in no way inferior to conventionally produced high-performance tools.
Fraunhofer IKTS counts decades of proven expertise in the development of hardmetals. To date, reliable cutting, drilling, pressing and stamping tools made of...
28.09.2016 | Event News
27.09.2016 | Event News
23.09.2016 | Event News
28.09.2016 | Medical Engineering
28.09.2016 | Materials Sciences
28.09.2016 | Business and Finance