For example, in a 2006 study of 180 men diagnosed with early stage prostate cancer via ultrasound-guided biopsy, nearly a quarter were upgraded to a more clinically significant stage of disease after 3D mapping biopsy found pockets of cancer the first technique had missed. Now, a University of Colorado Cancer Center study reports the locations of these most-missed pockets of prostate cancer.
Traditional, ultrasound-guided biopsies may miss cancer detected by the more accurate 3D mapping biopsies.
“There are three major reason we perform these 3D mapping biopsies in the clinic: first, a man may have rising PSA despite a series of negative biopsies and so want a more detailed opinion; second, a man may prefer additional reassurance that watching and waiting rather than treatment is the best course of action; and third, a man may pursue focal therapy in which only the cancerous sections of the prostate are removed and so need accurate information on the position of his cancer,” says Al Barqawi, MD, investigator at the CU Cancer Center, associate professor at the CU School of Medicine, and the paper’s senior author.
Barqawi is a pioneer of the 3D mapping biopsy technique, in which needle biopsies are taken 5mm apart across the x, y and z axes of a three-dimensional grid through the prostate, and has performed over 600 of the procedures.
The current study enrolled 161 men with a mean age of 61.6 years, who had been diagnosed with low-stage prostate cancer by ultrasound-guided biopsy. The study performed 3D mapping biopsies at a mean 192 days after the first and compared the results. Overall, ultrasound-guided biopsy found an average of 1.38 cancerous zones per patient, whereas 3D mapping biopsy found nearly three times the number of positive zones, at 3.33 per patient.
The follow-up findings from the 3D mapping study resulted in upgrading the severity of many of these seemingly low-grade cancers. Specifically, after first biopsy, 7.5 percent of patients had been graded Gleason 7 – the lowest grade at which treatment is considered “medium risk” and for which treatment is a reasonable option – and after second biopsy the percentage increased to twenty-five. After first biopsy, no patients had been scored above Gleason 7, and after 3D mapping biopsy, 4 percent were found to have Gleason 8, and 2 percent had Gleason 9.
“But we already knew that 3D mapping was likely to upgrade a prostate cancer’s Gleason score,” Barqawi says. “What we hoped to discover in this study is exactly where cancer is being missed by ultrasound-guided biopsy.”
Of these 161 total cases, cancer was found in the left-mid section of the prostate 62 times after it had been missed by ultrasound-guided biopsy. Likewise, 3D mapping found 62 unreported cancers in the right-mid section and 41 undetected cancers in the left-apex zone.
“This study adds to our knowledge about the interface and best uses of these two techniques. The cost and invasiveness of 3d mapping biopsy make it inappropriate for screening, but our message is that with the confirmation or strong suspicion of cancer, 3D mapping biopsy offers a much more accurate assessment of the location, stage and risk,” Barqawi says.
Garth Sundem | EurekAlert!
Termination of lethal arrhythmia with light
13.09.2016 | Rheinische Friedrich-Wilhelms-Universität Bonn
Sensor systems identify senior citizens at risk of falling within 3 weeks
29.08.2016 | University of Missouri-Columbia
Optical quantum computers can revolutionize computer technology. A team of researchers led by scientists from Münster University and KIT now succeeded in putting a quantum optical experimental set-up onto a chip. In doing so, they have met one of the requirements for making it possible to use photonic circuits for optical quantum computers.
Optical quantum computers are what people are pinning their hopes on for tomorrow’s computer technology – whether for tap-proof data encryption, ultrafast...
The Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP has been developing various applications for OLED microdisplays based on organic semiconductors. By integrating the capabilities of an image sensor directly into the microdisplay, eye movements can be recorded by the smart glasses and utilized for guidance and control functions, as one example. The new design will be debuted at Augmented World Expo Europe (AWE) in Berlin at Booth B25, October 18th – 19th.
“Augmented-reality” and “wearables” have become terms we encounter almost daily. Both can make daily life a little simpler and provide valuable assistance for...
With the help of artificial intelligence, chemists from the University of Basel in Switzerland have computed the characteristics of about two million crystals made up of four chemical elements. The researchers were able to identify 90 previously unknown thermodynamically stable crystals that can be regarded as new materials. They report on their findings in the scientific journal Physical Review Letters.
Elpasolite is a glassy, transparent, shiny and soft mineral with a cubic crystal structure. First discovered in El Paso County (Colorado, USA), it can also be...
For the first time, Fraunhofer IKTS shows additively manufactured hardmetal tools at WorldPM 2016 in Hamburg. Mechanical, chemical as well as a high heat resistance and extreme hardness are required from tools that are used in mechanical and automotive engineering or in plastics and building materials industry. Researchers at the Fraunhofer Institute for Ceramic Technologies and Systems IKTS in Dresden managed the production of complex hardmetal tools via 3D printing in a quality that are in no way inferior to conventionally produced high-performance tools.
Fraunhofer IKTS counts decades of proven expertise in the development of hardmetals. To date, reliable cutting, drilling, pressing and stamping tools made of...
At AKL’16, the International Laser Technology Congress held in May this year, interest in the topic of process control was greater than expected. Appropriately, the event was also used to launch the Industry Working Group for Process Control in Laser Material Processing. The group provides a forum for representatives from industry and research to initiate pre-competitive projects and discuss issues such as standards, potential cost savings and feasibility.
In the age of industry 4.0, laser technology is firmly established within manufacturing. A wide variety of laser techniques – from USP ablation and additive...
27.09.2016 | Event News
23.09.2016 | Event News
20.09.2016 | Event News
27.09.2016 | Life Sciences
27.09.2016 | Physics and Astronomy
27.09.2016 | Life Sciences