Infant milk formula is a widely accepted alternative to breast milk for babies in their first year of life. Since breast milk contains all the nutrients required by young infants, formula manufacturers aim to closely match their product’s ingredients to those of breast milk.
“Functional proteins in human milk are essential for key biological functions such as immune system development,” explains Ruige Wu from the A*STAR Singapore Institute of Manufacturing Technology. “However, some of these proteins are not found, or are present at lower concentrations, in infant formula products compared to human milk.”
Recently, some manufacturers began advertising that their products contained elevated levels of functional proteins, such as á-lactalbumin and immunoglobulin G. “The ability to measure these functional proteins is very important to control and monitor the quality of infant formula products,” explains Wu. “Supplementation of formula products is expected to be regulated shortly.”
Regulation of these products requires an easy and inexpensive quantitative method to detect low levels of functional proteins in milk, which also contains abundant other proteins. However, Wu explains that existing techniques, based on high-performance liquid chromatography (HPLC), use expensive equipment and time-consuming methods, with pretreatment alone taking several hours. She and her co-workers have now developed a microchip capillary-electrophoresis (CE)-based method that is cheaper, has a shorter assay time and eliminates the need for pretreatment (1).
Wu’s team fabricated a custom-made, microfluidic-chip CE device. The device separates the functional proteins from other, more abundant proteins in the formula using isoelectric focusing. In this process, the proteins move through a gel with a pH gradient, and the point at which they stop on the gel depends on their charge. Since each protein has a slightly different charge, separation occurs. This takes just two minutes.
“The functional proteins are then transferred into the embedded capillary for further separation according to their mass-to-charge ratio,” explains Wu. This capillary zone electrophoresis separation step takes 18 minutes. The team then identified and measured the amount of protein present—while still on the CE column—using ultraviolet detection. “The concentrations of functional proteins are determined from the respective absorbance values and calibration curves,” she says.
The reliability of the device was tested with infant milk formula samples spiked with known amounts of various functional proteins. “Results close to 100 per cent recovery were obtained,” says Wu.
“Our next steps are to collaborate with industry partners in the manufacturing, or quality-control testing, of infant formula or similar protein rich products,” she says.
The A*STAR-affiliated researchers contributing to this research are from the Singapore Institute of Manufacturing Technology
Wu, R., Wang, Z., Zhao, W., Yeung, W. S.-B. & Fung, Y. S. Multi-dimension microchip-capillary electrophoresis device for determination of functional proteins in infant milk formula. Journal of Chromatography A 1304, 220–226 (2013)
New switch decides between genome repair and death of cells
27.09.2016 | University of Cologne - Universität zu Köln
A blue stoplight to prevent runaway photosynthesis
27.09.2016 | National Institute for Basic Biology
Optical quantum computers can revolutionize computer technology. A team of researchers led by scientists from Münster University and KIT now succeeded in putting a quantum optical experimental set-up onto a chip. In doing so, they have met one of the requirements for making it possible to use photonic circuits for optical quantum computers.
Optical quantum computers are what people are pinning their hopes on for tomorrow’s computer technology – whether for tap-proof data encryption, ultrafast...
The Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP has been developing various applications for OLED microdisplays based on organic semiconductors. By integrating the capabilities of an image sensor directly into the microdisplay, eye movements can be recorded by the smart glasses and utilized for guidance and control functions, as one example. The new design will be debuted at Augmented World Expo Europe (AWE) in Berlin at Booth B25, October 18th – 19th.
“Augmented-reality” and “wearables” have become terms we encounter almost daily. Both can make daily life a little simpler and provide valuable assistance for...
With the help of artificial intelligence, chemists from the University of Basel in Switzerland have computed the characteristics of about two million crystals made up of four chemical elements. The researchers were able to identify 90 previously unknown thermodynamically stable crystals that can be regarded as new materials. They report on their findings in the scientific journal Physical Review Letters.
Elpasolite is a glassy, transparent, shiny and soft mineral with a cubic crystal structure. First discovered in El Paso County (Colorado, USA), it can also be...
For the first time, Fraunhofer IKTS shows additively manufactured hardmetal tools at WorldPM 2016 in Hamburg. Mechanical, chemical as well as a high heat resistance and extreme hardness are required from tools that are used in mechanical and automotive engineering or in plastics and building materials industry. Researchers at the Fraunhofer Institute for Ceramic Technologies and Systems IKTS in Dresden managed the production of complex hardmetal tools via 3D printing in a quality that are in no way inferior to conventionally produced high-performance tools.
Fraunhofer IKTS counts decades of proven expertise in the development of hardmetals. To date, reliable cutting, drilling, pressing and stamping tools made of...
At AKL’16, the International Laser Technology Congress held in May this year, interest in the topic of process control was greater than expected. Appropriately, the event was also used to launch the Industry Working Group for Process Control in Laser Material Processing. The group provides a forum for representatives from industry and research to initiate pre-competitive projects and discuss issues such as standards, potential cost savings and feasibility.
In the age of industry 4.0, laser technology is firmly established within manufacturing. A wide variety of laser techniques – from USP ablation and additive...
27.09.2016 | Event News
23.09.2016 | Event News
20.09.2016 | Event News
27.09.2016 | Life Sciences
27.09.2016 | Physics and Astronomy
27.09.2016 | Life Sciences