Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Research Shows That Reported Oil Sands Emissions Greatly Underestimated

06.02.2014
A new comprehensive modeling assessment of contamination in the Athabasca Oil Sands Region indicates that officially reported emissions of certain hazardous air pollutants have been greatly underestimated.

The results of the assessment, which was carried out by University of Toronto Scarborough Environmental Chemistry professor Frank Wania and his PhD candidate Abha Parajulee, will be published in the Proceedings of the National Academy of Science Monday, February 3 2014. The study constitutes the most comprehensive such model that has been done for the Oil Sands Region.

The team used a model to assess the plausibility of reported emissions of a group of atmospheric pollutants known as polycyclic aromatic hydrocarbons (PAHs). Many PAHs are highly carcinogenic.

“When dealing with chemicals that have the potential to harm people and animals, it is vital that we have a good understanding of how, and how much they are entering the environment,” said Parajulee, the lead author of the paper.

PAHs are released during the process of extracting petroleum from the oil sands. Environmental Impact Assessments have so far only considered the PAHs that are released directly into the atmosphere. The risk associated with those direct releases was judged to fall within acceptable regulatory limits.

The model used by Parajulee and Wania takes into account other indirect pathways for the release of PAHs that hadn’t been assessed before or were deemed negligible. For instance, they found that evaporation from tailings ponds – lakes of polluted water also created through oil sands processing – may actually introduce more PAHs into the atmosphere than direct emissions.

“Tailings ponds are not the end of the journey for many of the pollutants they contain. Some PAHs are volatile, meaning they escape into the air much more than many people think,” says Parajulee. (pictured seated at right with Wania).

The higher levels of PAHs the UTSC scientists’ model predicts when accounting for emissions from tailings ponds are consistent with what has actually been measured in samples taken from areas near and in the Athabasca Oil Sands Region.

The authors also found, however, that tailings ponds emissions are likely not significant contributors of relatively involatile PAHs to the Oil Sands Region atmosphere. Instead, other emissions sources not taken into account by the environmental impact assessment, such as blowing dust, are probably more important for these chemicals.

The pair of researchers modeled only three PAHs, which they believe are representative of others. Still, they say, their model indicates better monitoring data and emissions information are needed to improve our understanding of the environmental impact of the oil sands even further.

“Our study implies that PAH concentrations in air, water, and food, that are estimated as part of environmental impact assessments of oil sands mining operations are very likely too low,” says Wania. “Therefore the potential risks to humans and wildlife may also have been underestimated.”

Don Campbell | Newswise
Further information:
http://www.utoronto.ca

More articles from Ecology, The Environment and Conservation:

nachricht How to detect water contamination in situ?
22.09.2016 | Tomsk Polytechnic University (TPU)

nachricht Quantifying the chemical effects of air pollutants on oxidative stress and human health
12.09.2016 | Max-Planck-Institut für Chemie

All articles from Ecology, The Environment and Conservation >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: OLED microdisplays in data glasses for improved human-machine interaction

The Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP has been developing various applications for OLED microdisplays based on organic semiconductors. By integrating the capabilities of an image sensor directly into the microdisplay, eye movements can be recorded by the smart glasses and utilized for guidance and control functions, as one example. The new design will be debuted at Augmented World Expo Europe (AWE) in Berlin at Booth B25, October 18th – 19th.

“Augmented-reality” and “wearables” have become terms we encounter almost daily. Both can make daily life a little simpler and provide valuable assistance for...

Im Focus: Artificial Intelligence Helps in the Discovery of New Materials

With the help of artificial intelligence, chemists from the University of Basel in Switzerland have computed the characteristics of about two million crystals made up of four chemical elements. The researchers were able to identify 90 previously unknown thermodynamically stable crystals that can be regarded as new materials. They report on their findings in the scientific journal Physical Review Letters.

Elpasolite is a glassy, transparent, shiny and soft mineral with a cubic crystal structure. First discovered in El Paso County (Colorado, USA), it can also be...

Im Focus: Complex hardmetal tools out of the 3D printer

For the first time, Fraunhofer IKTS shows additively manufactured hardmetal tools at WorldPM 2016 in Hamburg. Mechanical, chemical as well as a high heat resistance and extreme hardness are required from tools that are used in mechanical and automotive engineering or in plastics and building materials industry. Researchers at the Fraunhofer Institute for Ceramic Technologies and Systems IKTS in Dresden managed the production of complex hardmetal tools via 3D printing in a quality that are in no way inferior to conventionally produced high-performance tools.

Fraunhofer IKTS counts decades of proven expertise in the development of hardmetals. To date, reliable cutting, drilling, pressing and stamping tools made of...

Im Focus: Launch of New Industry Working Group for Process Control in Laser Material Processing

At AKL’16, the International Laser Technology Congress held in May this year, interest in the topic of process control was greater than expected. Appropriately, the event was also used to launch the Industry Working Group for Process Control in Laser Material Processing. The group provides a forum for representatives from industry and research to initiate pre-competitive projects and discuss issues such as standards, potential cost savings and feasibility.

In the age of industry 4.0, laser technology is firmly established within manufacturing. A wide variety of laser techniques – from USP ablation and additive...

Im Focus: New laser joining technologies at ‘K 2016’ trade fair

Every three years, the plastics industry gathers at K, the international trade fair for plastics and rubber in Düsseldorf. The Fraunhofer Institute for Laser Technology ILT will also be attending again and presenting many innovative technologies, such as for joining plastics and metals using ultrashort pulse lasers. From October 19 to 26, you can find the Fraunhofer ILT at the joint Fraunhofer booth SC01 in Hall 7.

K is the world’s largest trade fair for the plastics and rubber industry. As in previous years, the organizers are expecting 3,000 exhibitors and more than...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

Experts from industry and academia discuss the future mobile telecommunications standard 5G

23.09.2016 | Event News

ICPE in Graz for the seventh time

20.09.2016 | Event News

Using mathematical models to understand our brain

16.09.2016 | Event News

 
Latest News

Chains of nanogold – forged with atomic precision

23.09.2016 | Life Sciences

New leukemia treatment offers hope

23.09.2016 | Health and Medicine

Self-assembled nanostructures hit their target

23.09.2016 | Life Sciences

VideoLinks
B2B-VideoLinks
More VideoLinks >>>