Asthma attacks, wheezing, cardiovascular diseases and lung cancer are some of the more glaring examples of diseases we - in worst case - can get from the domestic air. The list of injuries due to air pollution in Denmark is long.
This appears from a brand new article that professor Ole Hertel from Aarhus University, has written with a number of Danish colleagues at University of Copenhagen, the Danish Cancer Society and Aarhus University.
"So the list of diseases detected in Denmark is long, but it does not mean that we have the world's most polluted air. This is to be found in Asia, Africa and South America. Here, you typically find a yearly mean value of the particle pollution (PM10) of 50-200 micrograms per cubic metres of air, while the content in Copenhagen and other Western European Megacities typically is at a lower level - about 20-50 micrograms per cubic metre. But even in a "moderately polluted" air as we call it in Danish towns and cities, we find many serious injuries which come from the air that we breathe every day," explains Ole Hertel.
In the article "Utilizing Monitoring Data and Spatial Analysis Tools for Exposure Assessment of Atmospheric Pollutants in Denmark", Ole Hertel and his colleagues review the Danish experiences in combining measurements and models. By combining measurements on relatively few but well-chosen places with advanced models for spreading of air pollution, the researchers can calculate the air pollution down to the individual addresses.
Hertel and Co. review a number of Danish studies of the coherence between air pollution and injuries to health. A total of nine short-term studies have been published in Denmark, where researchers have demonstrated respiratory and cardiovascular diseases after episodes with increased air pollution, etc. Similarly, eleven studies demonstrate long-term injuries due to air pollution, e.g. lung cancer, cardiovascular diseases, diabetes and mortality.
The scientists' ability to detect a wide range if different types of damages of the Danes' health is due to the fact that Danish researchers represent some of the very best to demonstrate illnesses caused by air pollution on human health. This is obvious when we look at the model for spreading of air pollution, OSPM, which was developed by Danes and is now used in approx. twenty countries. This is also why Ole Hertel was invited to give an overview of the diseases detected to be a consequence of the air pollution in Denmark, first on a major international conference and afterwards in book form:
"We have some very unique health registers in Denmark and that is quite different from other countries. We are able to connect addresses and health registers with air-polluted areas. In Denmark, we have many cohort investigations where the same persons are followed during a long period of time. Here, we can link to other sorts of information and thus separate effects related to e.g. lifestyle from effects related to air pollution. For instance, the Danish Cancer Society makes a study of people's diet and exercise habits in a so-called Diet, Cancer, Health study, and in addition you have the whole birth cohort where the same children have been followed from around the turn of the century until now," explains Ole Hertel.
But not only do we have some of the world's best health registers in Denmark;
"We also have some outstanding good pieces of information on traffic, buildings and infrastructure. This information we have concluded in the so-called
AirGis Model which uses digital road maps and building and road registers to determine the parameters we need for air quality calculations on address level. Therefore, we can come up with conclusions that are more precise than in other countries." Ole Hertel emphasises that there are strong constrains around handling of personal information.
Ole Hertel points out one of the Danish results as particularly notable:
"It came as a surprise to me that the studies showed a connection between air pollution and diabetes. It is rather new information that air pollution can cause diabetes, and we are working on finding a biological explanation for this correlation. This is an example of the fact that our very detailed way of working in Denmark leads to precise results."
It takes fifty litres of air to read this article
Dear reader, if you represent an average reader, you have just spent three minutes and 58 seconds to read this article - probably inclusive of pauses for thoughts (thank you for that!). During this time you have inhaled approx. fifty litres of air through your lungs, depending on your gender and size.
Professor Ole Hertel, Aarhus University, Department of Environmental Science, tel. +45 8715 8514 email@example.com
Utilizing Monitoring data and Spatial Analysis Tools for exposure Assessment of Atmospheric Pollutants in Denmark, Hertel, O., etc. 2013. In: Occurrence, fate and Impact of Atmospheric Pollutants on Environmental and Human Health; rapporteur: Mr McConnell, L. etc. AC union areas Symposium Series; American Chemical Society: Washington, DC. DOI: 10.1021 /BK-2013-1149.ch006, p. 95-122.
Ole Hertel | EurekAlert!
Malaysia's unique freshwater mussels in danger
27.09.2016 | The University of Nottingham Malaysia Campus
How to detect water contamination in situ?
22.09.2016 | Tomsk Polytechnic University (TPU)
Optical quantum computers can revolutionize computer technology. A team of researchers led by scientists from Münster University and KIT now succeeded in putting a quantum optical experimental set-up onto a chip. In doing so, they have met one of the requirements for making it possible to use photonic circuits for optical quantum computers.
Optical quantum computers are what people are pinning their hopes on for tomorrow’s computer technology – whether for tap-proof data encryption, ultrafast...
The Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP has been developing various applications for OLED microdisplays based on organic semiconductors. By integrating the capabilities of an image sensor directly into the microdisplay, eye movements can be recorded by the smart glasses and utilized for guidance and control functions, as one example. The new design will be debuted at Augmented World Expo Europe (AWE) in Berlin at Booth B25, October 18th – 19th.
“Augmented-reality” and “wearables” have become terms we encounter almost daily. Both can make daily life a little simpler and provide valuable assistance for...
With the help of artificial intelligence, chemists from the University of Basel in Switzerland have computed the characteristics of about two million crystals made up of four chemical elements. The researchers were able to identify 90 previously unknown thermodynamically stable crystals that can be regarded as new materials. They report on their findings in the scientific journal Physical Review Letters.
Elpasolite is a glassy, transparent, shiny and soft mineral with a cubic crystal structure. First discovered in El Paso County (Colorado, USA), it can also be...
For the first time, Fraunhofer IKTS shows additively manufactured hardmetal tools at WorldPM 2016 in Hamburg. Mechanical, chemical as well as a high heat resistance and extreme hardness are required from tools that are used in mechanical and automotive engineering or in plastics and building materials industry. Researchers at the Fraunhofer Institute for Ceramic Technologies and Systems IKTS in Dresden managed the production of complex hardmetal tools via 3D printing in a quality that are in no way inferior to conventionally produced high-performance tools.
Fraunhofer IKTS counts decades of proven expertise in the development of hardmetals. To date, reliable cutting, drilling, pressing and stamping tools made of...
At AKL’16, the International Laser Technology Congress held in May this year, interest in the topic of process control was greater than expected. Appropriately, the event was also used to launch the Industry Working Group for Process Control in Laser Material Processing. The group provides a forum for representatives from industry and research to initiate pre-competitive projects and discuss issues such as standards, potential cost savings and feasibility.
In the age of industry 4.0, laser technology is firmly established within manufacturing. A wide variety of laser techniques – from USP ablation and additive...
27.09.2016 | Event News
23.09.2016 | Event News
20.09.2016 | Event News
27.09.2016 | Life Sciences
27.09.2016 | Physics and Astronomy
27.09.2016 | Life Sciences