Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Laser Simplifies Mainte­nance in Casting Plants

25.02.2013
An optical measuring system developed by Siemens reduces maintenance requirements in continuous casting plants by simplifying the process for aligning the rolls along long lines between which hot steel strands are guided.

All the rolls have to be precisely vertically aligned to ensure the mechanical stresses they are exposed to are equally distributed. Up into now, the roll positions have been measured and documented manually in an expensive process that's also prone to error.



The new laser system provides highly precise digital measurements that take less time to complete. Measurement data is sent directly to the control unit, which prevents errors caused by manual data transfer. The data also allows technicians to monitor conditions at the plant, which means maintenance can be carried out in line with actual needs rather than at set intervals, which was previously the case.

Continuous casting plants cast liquid steel into slabs a few meters long and several centimeters thick. These slabs are guided along long lines between rolls. The rolls must be precisely vertically aligned. If they are not, they will be exposed to varying levels of pressure from the slab and will also exert different levels of pressure on the latter, which can negatively impact slab quality and damage the roll bearings.

The rolls are regularly calibrated to prevent these problems. The process involves removing individual segments of the strand guide line. Each segment contains several rolls, and measurements are taken by holding an iron ruler several meters long at a specific height above the rolls. Workers then measure the distance of each roll to the ruler and write down the results. This method takes time, can lead to errors, and becomes imprecise in the middle because the ruler bends at that point.

The new Simetal Opal laser measuring system measures all spots with equal precision and is very easy to use. The system's rotating laser emits beams that generate a reference line parallel to the top side of the rolls. A linear photodetector is vertically mounted on the rolls.

The distance between a roll and reference line is determined according to which photodetector segment the laser beam hits. Workers move along the line and place the detector on each roll, whose alignment is then precisely measured down to less than one-tenth of a millimeter.

Simetal Opal is part of a continuous casting plant monitoring concept developed by Siemens. The system can be integrated into existing plants and is already being used in the manufacturing process at the Siemens facility in Shanghai.

Dr. Norbert Aschenbrenner | Siemens InnovationNews
Further information:
http://www.siemens.com/innovationnews

More articles from Machine Engineering:

nachricht Process-Integrated Inspection for Ultrasound-Supported Friction Stir Welding of Metal Hybrid-Joints
27.09.2016 | Fraunhofer-Institut für Zerstörungsfreie Prüfverfahren IZFP

nachricht Lightweight robots in manual assembly
13.09.2016 | Fraunhofer-Institut für Arbeitswirtschaft und Organisation IAO

All articles from Machine Engineering >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: New welding process joins dissimilar sheets better

Friction stir welding is a still-young and thus often unfamiliar pressure welding process for joining flat components and semi-finished components made of light metals.
Scientists at the University of Stuttgart have now developed two new process variants that will considerably expand the areas of application for friction stir welding.
Technologie-Lizenz-Büro (TLB) GmbH supports the University of Stuttgart in patenting and marketing its innovations.

Friction stir welding is a still-young and thus often unfamiliar pressure welding process for joining flat components and semi-finished components made of...

Im Focus: First quantum photonic circuit with electrically driven light source

Optical quantum computers can revolutionize computer technology. A team of researchers led by scientists from Münster University and KIT now succeeded in putting a quantum optical experimental set-up onto a chip. In doing so, they have met one of the requirements for making it possible to use photonic circuits for optical quantum computers.

Optical quantum computers are what people are pinning their hopes on for tomorrow’s computer technology – whether for tap-proof data encryption, ultrafast...

Im Focus: OLED microdisplays in data glasses for improved human-machine interaction

The Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP has been developing various applications for OLED microdisplays based on organic semiconductors. By integrating the capabilities of an image sensor directly into the microdisplay, eye movements can be recorded by the smart glasses and utilized for guidance and control functions, as one example. The new design will be debuted at Augmented World Expo Europe (AWE) in Berlin at Booth B25, October 18th – 19th.

“Augmented-reality” and “wearables” have become terms we encounter almost daily. Both can make daily life a little simpler and provide valuable assistance for...

Im Focus: Artificial Intelligence Helps in the Discovery of New Materials

With the help of artificial intelligence, chemists from the University of Basel in Switzerland have computed the characteristics of about two million crystals made up of four chemical elements. The researchers were able to identify 90 previously unknown thermodynamically stable crystals that can be regarded as new materials. They report on their findings in the scientific journal Physical Review Letters.

Elpasolite is a glassy, transparent, shiny and soft mineral with a cubic crystal structure. First discovered in El Paso County (Colorado, USA), it can also be...

Im Focus: Complex hardmetal tools out of the 3D printer

For the first time, Fraunhofer IKTS shows additively manufactured hardmetal tools at WorldPM 2016 in Hamburg. Mechanical, chemical as well as a high heat resistance and extreme hardness are required from tools that are used in mechanical and automotive engineering or in plastics and building materials industry. Researchers at the Fraunhofer Institute for Ceramic Technologies and Systems IKTS in Dresden managed the production of complex hardmetal tools via 3D printing in a quality that are in no way inferior to conventionally produced high-performance tools.

Fraunhofer IKTS counts decades of proven expertise in the development of hardmetals. To date, reliable cutting, drilling, pressing and stamping tools made of...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

HLF: From an experiment to an establishment

29.09.2016 | Event News

European Health Forum Gastein 2016 kicks off today

28.09.2016 | Event News

Laser use for neurosurgery and biofabrication - LaserForum 2016 focuses on medical technology

27.09.2016 | Event News

 
Latest News

New Multiferroic Materials from Building Blocks

29.09.2016 | Materials Sciences

Silicon Fluorescent Material Developed Enabling Observations under a Bright “Biological Optical Window”

29.09.2016 | Materials Sciences

X-shape Bio-inspired Structures

29.09.2016 | Interdisciplinary Research

VideoLinks
B2B-VideoLinks
More VideoLinks >>>