Forum for Science, Industry and Business

Sponsored by:     3M 
Search our Site:

 

Hydrothermal liquefaction -- the most promising path to a sustainable bio-oil production

07.02.2013
Scientists at 2 Danish universities have made a major breakthrough in producing high-quality and cost-effective bio-oil using hydrothermal liquefaction

A new generation of the HTL process can convert all kinds of biomasses to crude bio-oil, which is sufficiently similar to fossil crude oil that a simple thermal upgrade and existing refinery technology can be employed to subsequently obtain all the liquid fuels we know today.

What is more, the HTL process only consumes approximately 10-15 percent of the energy in the feedstock biomass, yielding an energy efficiency of 85-90 percent.

To emphasize, the HTL process accepts all biomasses from modern society – sewage sludge, manure, wood, compost and plant material along with waste from households, meat factories, dairy production and similar industries.

It is by far the most feedstock flexible of any liquid fuel producing process, including pyrolysis, bio-ethanol, gasification with Fischer-Tropsch or catalytic upgrading of different vegetable or agro-industrial residual oils, and does not carry higher costs than these.

Hydrothermal liquefaction is basically pressure cooking, but instead of cooking the biomass in batches, one pot-full at a time, this new generation of HTL is based on flow production, where the biomass is injected into a 400 °C pre-heated reactor, "cooked" under high pressure for ~15 minutes and then quickly cooled down to 70°C.

At 400°C and high pressure the water is in a supercritical state, neither liquid nor gas, at which it easily decomposes the biomass. The process is environmentally friendly, since no harmful solvents are involved, and the energy efficiency is very high: The HTL process only consumes approximately 10-15% of the energy in the feedstock biomass, because the heat energy is recycled between the heating and cooling of the process medium.

The wet medium means that HTL readily accepts moist or wet biomasses, such as those mentioned above. Wet biomasses are in vast majority on Earth. All other known processes for liquid bio-fuel production either require expensive drying or only make use of a limited proportion of the biomass, e.g. the carbohydrate content.

The water phase emanating from the HTL process has low carbon contents and can either be recycled into the process or ultimately be purified to attain drinking water quality, which is the long-term goal. As such HTL replaces the burden of disposal with the benefit of recycling.


The HTL process has the following benefits:
Crude HTL oil has high heating values of approximately 35-39 MJ/kg on a dry ash free basis
The HTL process only consumes approximately 10-15% of the energy in the feedstock biomass, yielding an energy efficiency of 85-90%
Crude HTL oil has very low oxygen, sulphur and water content (compared to e.g. pyrolysis oil which typically contains approx. 50% water)
HTL oil recovers more than 70% of the feedstock carbon content (single pass)
HTL oil is storage stable, and has comparatively low upgrading requirements, due in part to a high fraction of middle distillates in the crude oil. It is much less upgrading intensive than e.g. pyrolysis oil, which needs immediate upgrading in order not to deteriorate.

The bio-oil from HTL can be used as-produced in heavy engines or it can be hydrogenated or thermally upgraded to obtain diesel-, gasoline- or jet-fuels by existing refinery technology. In this sense, HTL bio-oil is directly comparable to fossil crude oil. This is unique among liquid bio-fuels and means that it can directly enter the existing fuel distribution network for automotive transportation in any concentration, giving it full drop-in properties.

In Denmark, Aarhus University and Aalborg University are in partnership on HTL research at all levels. In Aarhus, Dept. of Chemistry focuses on fundamental understanding of the process and quick surveys of the effects of different feedstocks and catalysts along with subsequent upgrading. Dept. of Agro-Ecology develops energy crops while Dept. of Engineering works on pilot-scale HTL. The latter is pursued even more vigorously at Aalborg University (Dept. of Energy Technology), which focuses strongly on pilot-scale production and process efficiency, as well as upgrading of HTL bio-oil along with end user testing of oils and upgraded distillates in engines and turbines. The Dept. of Biotechnology, Chemistry and Environmental Engineering, AAU Esbjerg, directs its activities towards extracting value not only from the oil, but also from the effluents.

The combined efforts and unique results already obtained hold promise of another energy technology endeavor in Denmark comparable only to the breakthrough of the windmill-industry in the 1980's.

About the HTL process:

- HTL operates in hot, compressed water at >300 degrees C and >200 bar, often assisted by catalysts
- Boiling is suppressed, i.e. no energy is expended to overcome the latent heat of evaporation
- Successful HTL is dependent on extremely swift heating and cooling of the biomass, in order to avoid the formation of tar or ash compounds
- Heat energy is recycled between the heating and cooling of the process medium
- A typical Pilot-scale plant yields ~30 liters of bio-oil per day – one such plant is being built at Aalborg University
- An industrial scale plant can be anything from 300 barrels per day up several thousand, comparable to fossil oil wells
- Some HTL has made use of heterogeneous as well as homogeneous catalysts, e.g. ZrO2

- Recently, Aarhus University has shown that ZrO2 has no effect on HTL of the biomass DDGS

Little-known facts on H2O:

- The boiling phenomenon of water is fully suppressed at pressures above 221 atm. This is called the critical pressure.
- There is also a critical temperature – 374oC
- At higher temperatures and pressures, water is said to be in the supercritical domain.
- At slightly lower temperatures (300-350oC) the near-critical domain exists.
- Near-critical water can sustain acid and base ions simultaneously to a factor of 1000 above concentrations at ambient conditions
- Supercritical water is non-polar and mixes freely with oil substances. It also promotes radical-driven chemistry.
- Most scientific literature agree that HTL works best at near-critical conditions

- Recently, Aarhus University has shown that the best HTL oil yields are in fact obtained at supercritical conditions

Jacob Becker | EurekAlert!
Further information:
http://www.au.dk

More articles from Power and Electrical Engineering:

nachricht Philippines’ microsatellite captures best-in-class high-resolution images
22.09.2016 | Hokkaido University

nachricht OLED microdisplays in data glasses for improved human-machine interaction
22.09.2016 | Fraunhofer-Institut für Organische Elektronik, Elektronenstrahl- und Plasmatechnik FEP

All articles from Power and Electrical Engineering >>>

The most recent press releases about innovation >>>

Die letzten 5 Focus-News des innovations-reports im Überblick:

Im Focus: OLED microdisplays in data glasses for improved human-machine interaction

The Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP has been developing various applications for OLED microdisplays based on organic semiconductors. By integrating the capabilities of an image sensor directly into the microdisplay, eye movements can be recorded by the smart glasses and utilized for guidance and control functions, as one example. The new design will be debuted at Augmented World Expo Europe (AWE) in Berlin at Booth B25, October 18th – 19th.

“Augmented-reality” and “wearables” have become terms we encounter almost daily. Both can make daily life a little simpler and provide valuable assistance for...

Im Focus: Artificial Intelligence Helps in the Discovery of New Materials

With the help of artificial intelligence, chemists from the University of Basel in Switzerland have computed the characteristics of about two million crystals made up of four chemical elements. The researchers were able to identify 90 previously unknown thermodynamically stable crystals that can be regarded as new materials. They report on their findings in the scientific journal Physical Review Letters.

Elpasolite is a glassy, transparent, shiny and soft mineral with a cubic crystal structure. First discovered in El Paso County (Colorado, USA), it can also be...

Im Focus: Complex hardmetal tools out of the 3D printer

For the first time, Fraunhofer IKTS shows additively manufactured hardmetal tools at WorldPM 2016 in Hamburg. Mechanical, chemical as well as a high heat resistance and extreme hardness are required from tools that are used in mechanical and automotive engineering or in plastics and building materials industry. Researchers at the Fraunhofer Institute for Ceramic Technologies and Systems IKTS in Dresden managed the production of complex hardmetal tools via 3D printing in a quality that are in no way inferior to conventionally produced high-performance tools.

Fraunhofer IKTS counts decades of proven expertise in the development of hardmetals. To date, reliable cutting, drilling, pressing and stamping tools made of...

Im Focus: Launch of New Industry Working Group for Process Control in Laser Material Processing

At AKL’16, the International Laser Technology Congress held in May this year, interest in the topic of process control was greater than expected. Appropriately, the event was also used to launch the Industry Working Group for Process Control in Laser Material Processing. The group provides a forum for representatives from industry and research to initiate pre-competitive projects and discuss issues such as standards, potential cost savings and feasibility.

In the age of industry 4.0, laser technology is firmly established within manufacturing. A wide variety of laser techniques – from USP ablation and additive...

Im Focus: New laser joining technologies at ‘K 2016’ trade fair

Every three years, the plastics industry gathers at K, the international trade fair for plastics and rubber in Düsseldorf. The Fraunhofer Institute for Laser Technology ILT will also be attending again and presenting many innovative technologies, such as for joining plastics and metals using ultrashort pulse lasers. From October 19 to 26, you can find the Fraunhofer ILT at the joint Fraunhofer booth SC01 in Hall 7.

K is the world’s largest trade fair for the plastics and rubber industry. As in previous years, the organizers are expecting 3,000 exhibitors and more than...

All Focus news of the innovation-report >>>

Anzeige

Anzeige

Event News

Experts from industry and academia discuss the future mobile telecommunications standard 5G

23.09.2016 | Event News

ICPE in Graz for the seventh time

20.09.2016 | Event News

Using mathematical models to understand our brain

16.09.2016 | Event News

 
Latest News

Chains of nanogold – forged with atomic precision

23.09.2016 | Life Sciences

New leukemia treatment offers hope

23.09.2016 | Health and Medicine

Self-assembled nanostructures hit their target

23.09.2016 | Life Sciences

VideoLinks
B2B-VideoLinks
More VideoLinks >>>